A control chart is to be formed for a process in which laptops are produced. The inspection unit is one laptop and control chart for the number of defects are to be used. Preliminary data are recorded and 90 defects are found in 40 laptops. Obtain the value of UCL & LCL of c- chart? None of these options 4.24; +0.26 4.24; -0.26 6.75: -2.25

A control chart is to be formed for a process in which laptops are produced. The inspection unit is one laptop and control chart for the number of defects are to be used. Preliminary data are recorded and 90 defects are found in 40 laptops. Obtain the value of UCL & LCL of c- chart? None of these options 4.24; +0.26 4.24; -0.26 6.75: -2.25

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

concernedas to whether caulking tubes are being properly capped. Ifa significant proportion of the tubes are not being sealed,Webster is placing its customers in a messy situation.Tubes are packaged in large boxes of 144. Several boxes areinspected, and the following numbers of leaking tubes arefound: Calculate p-chart three-sigma control limits to assesswhether the capping process is in statistical control.
An Xbar control chart designed with L=3 and sample size n=4 has control limits UCL=342.05 and LCL=317.95. If the mean shifts to mu1=335 beta is found to be 0.9603. What would be the ARL1 after the mean shifts to mu1? 4.2 10.06 2.03 not enough information 25.22
DESIGNING A CONTROL CHART EXAMPLE Fujiyama Electronics, Inc. has been having difficulties with circuit boards purchased from an outside supplier. Unacceptable variability occurs between two drilled holes that are supposed to be 5 cm apart on the circuit boards. Thirty samples of 4 boards each were taken from shipments from the supplier as shown in the data listed below. Construct x and R charts for the process using the following data. DATA Sample No Samples 1 4.92 4.26 4.94 4.29 2 4.65 5.54 5.00 5.42 3 5.77 5.26 4.76 4.79 4 6.25 4.88 5.66 4.44 5 5.27 5.41 6.02 4.91 6 5.22 5.38 5.08 4.65 7 5.47 4.68 4.56 4.70 8 5.71 4.54 4.17 4.87 9 5.24 5.58 4.72 5.41 10 4.42 5.18 4.79 4.73 11 5.14 4.26 4.71 5.48 12 4.92 5.78 5.50 5.05 13 5.79 3.83 4.30 4.78 14 4.92 4.80 4.75 5.59 15 5.68…
A shirt manufacturer buys cloth by the roll from a supplier. For setting up a control chart to manage the irregularities (e.g., loose threads and tears), the following data were collected from a sample provided by the supplier. Sample Irregularities 1 2 2 1 3 4 4 2 5 0 6 4 7 3 8 0 9 2 10 1 Total 19 Calculate the LCL and UCL for a c-chart with z=2 LCL= 0, UCL = 4.66 LCL= 0, UCL = 3.28 LCL= -0.86, UCL = 3.28 LCL= -0.86, UCL = 3.51 LCL= -0.86, UCL = 4.66
need answer ASAP ... will upvote if correct
Control charts for X-bar and R are maintained for the tensile strength of fibers used in composite materials. The specifications are 440+40. After 36 samples of size n=7 are analyzed, we find that: 36 36 X¡ = 12,870 Ri = 1,350 i=1 What are the limits of the X-bar chart? UCL=442.86 and LCL=415.14 UCL=531.43 and LCL=498.17 UCL=415.18 and LCL=389.19 UCL=373.21 and LCL=341.79 UCL=335.89 and LCL=307.61
Five data entry operators work at the data process-ing department of the Birmingham Bank. Each day for 30 days, the number of defective records in a sample of 250 records typedby these operators has been noted, as follows: a) Establish 3s upper and lower control limits.b) Why can the lower control limit not be a negative number? c) The industry standards for the upper and lower control lim-its are 0.10 and 0.01, respectively. What does this imply about Birmingham Bank’s own standards?
Management at Webster Chemical Company is concerned as to whether caulking tubes are being properly capped. If a significant proportion of the tubes are not being sealed, Webster is placing its customers in a messy situation. Tubes are packaged in large boxes of 135. Several boxes are inspected, and the following numbers of leaking tubes are found: View an example Sample 1 2 3 Get more help. 4 Tubes 7 7 8 5 1 5 6 7 Calculate p-chart three-sigma control limits to assess whether the capping process is in statistical control. The UCL, equals 1 Sample 8 8 9 10 11 12 13 14 Tubes 7 2 4 8 6 9 MacBook Pro 3 Sample 15 16 17 18 19 20 Total Tubes 8 3 3 5 and the LCL equals (Enter your responses rounded to three decimal places. If your answer for LCL, is negative, enter this value as 0.) 3 6 104 Clear all Check answer O
Do control charts assist in monitoring quality as conformance or quality as improvement?
A manufacturer uses statistical process control to control the quality of the firm's products. Samples of 50 of Product A are taken, and a defective/acceptable decision is made on each unit sampled. For Product B, the number of flaws per unit is counted. What type(s) of control charts should be used? Select one: a. c-chart for A, mean and range charts for B b. p-chart for A , mean and range charts for B c. c-chart for both A and B d. p-chart for A, c-chart for B e. p-charts for both A and B
A metal fabricator produces connecting rods with an outer diameter that has a 1" ± 0.04 inch specification. A machine operator takes several sample measurements over time and determines the sample mean outer diameter to be 1 inch with a standard deviation of 0.008 inch. Calculate the process capability. 1.44 1.31 2.50 1.67 1.61
Please do not give solution in image format thanku