A constant force of ''F'' acts on a mass as shown. The mass starts its motion from rest at position 1, the unstretched length of the spring is 250 mm, and the spring modulus is k=1,5 k?/m. Neglecting the friction, determine the required force ''F'' to cause the 2−kg mass to have a speed of v2=1,5 m/s at position 2.

Q: Rod OA rotates counterclockwise at a constant angular rate θ˙ = 4 rad/s. The double collar B is…

A:

Q: A truck of mass 10 tonnes was moving with a velocity of 130 km/hr. The brakes were applied to bring…

A:

Q: This kayaker starts at rest (v=0) and paddles for 3 seconds. The force of the paddle on the water is…

A:

Q: The mass of block A and B is 16 kg and 45 kg, respectively. Block A is attached to a linear spring…

A: Given:mA=16 KgmB=45 KgK=25 N/mh=2 mα=40°μk=0.25

Q: B 3 m -6 m- A hass at G. Initially, at take-off, the engines provide a thrust

A: 2T=2kN.. T'=1.7kN mass of aircraft=25000kg

Q: If its angular rate of rotation is constant and equals 6 rad/s, determine the horizontal tangential…

A: Solution: Given Data: m=2 kgr=0.4θθ.=6 rad/sθ=45o   To Find: (a) Horizontal tangential force, P? (b)…

Q: The super-container vessel has a total mass displacement of 23000 long tons. This vessel towed by a…

A: The velocity is v=2 knot=2×0.5144=1.0288 m/s The horizontal component of force is…

Q: The motion of block E shown in the figure is harmonic and is defined by the equation yE =0.15…

A:

Q: The spool, which has a mass of 2 kg, slides along the smooth horizontal spiral rod, r= (0.408) m,…

A: Solution:Given Data:To Find:(a) Horizontal tangential force, P?(b) Horizontal normal force, N?

Q: The 31-kg disk is originally spinning at w = 185 rad/s. It is placed on the ground, for which the…

A:

Q: block with some mass m is connected to a string that is attached to the ceiling. The block on the…

A:

Q: Determine the constant force P

A:

Q: Question a) The 10-kg block has a speed of 4 m/s when the force of F = (8t²) N is applied (Figure…

A:

Q: A 100-kg box is towed to move horizontally from rest by a constant force P=200 N. The kinetic…

A:

Q: the 75 n crate is released from rest in incline surface at time t=0. The coefficient of kinetic…

A:

Q: m R

A:

Q: The system is released from rest with no slack in the cable and with the spring stretched 110 mm.…

A:

Q: The coefficient of kinetic friction between the block and the surface is μ = 0.4. If the block is…

A: Coefficient of Kinetic friction. μk=0.4 Initial speed of the block. v0=2m/s Mass of the block.…

Q: Р.3) A collar of mass m = 2 kg is constrained %3D to move in the vertical plane along a rough rod of…

A: Consider the free body diagram as shown below for the collar.

Q: The rod of negligible mass is subjected to a couple moment of M = (30t²) N-m and the engine of the…

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: The slotted arm OA rotates about a horizontal axis through point O. The 0.18-kg slider P moves with…

A: it appears to be the same problem we discussed previously regarding the slotted arm OA rotating…

Q: a 7.4 lb block has a speed of v-2.4 ft/s to the left when the force of F=3.6t^3 lb is applied to the…

A: Given: The weight of block, m = 7.4 lb The speed of block, v = 2.4 ft/s The force acting, F = 3.6t^3…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.