The system is at rest with the spring unstretched when = 0. The 3-kg particle is then given a slight nudge to the right. (a) If the system comes to mo- mentary rest at 0= 40°, determine the spring con- stant k. (b) For the value k = 100 N/m, find the speed of the particle when 0 = 25°. Use the value b = 0.40 m throughout and neglect friction. B b m Problem 3/170 A 1.256

Q: The mass of block A and B is 16 kg and 45 kg, respectively. Block A is attached to a linear spring…

A: Given:mA=16 KgmB=45 KgK=25 N/mh=2 mα=40°μk=0.25

Q: The 47-kg crate is projected along the floor with an initial speed of vo = 8.5 m/s at x = 0. The…

A: The m = 47-kg crate is projected along the floor with an initial speed of V0 = 8.5 m/s at x = 0. The…

Q: The roller coaster car has a mass of 900 kg, including its passenger. It starts from the top of the…

A:

Q: The 1 kg sleeve is pulled to the configuration shown and released from rest. The spring has an…

A: Given : Force, F = 2 N Mass of sleeve, m = 1 kg Spring constant, k = 5N/m Length of unstretched…

Q: The small collar of mass m = 0.70 kg is released from rest at A and slides down the curved rod in…

A: Given data: m=0.77 kgb=0.67 mh=3.33 m Need to determine the velocity of the collar at B.

Q: gure 200 ft AKK P < -200 ft 1 of 1 - 200 (40 000-x²) x

A: Given,

Q: Determine the constant force P

A:

Q: The 4,450kg truck is traveling at 30.50m/s when the brakes on all its wheels are applied, causing it…

A: Given Data  Mass of the truck, mt=4450 Kg Mass of the boat + trailor, 2250Kg Total mass=6700Kg

Q: The 1.7-kg collar is at rest in position A when the constant force P is applied as shown. Determine…

A:

Q: Part A If the box strikes the smooth plate, which has a weight of 23 lb and is held in position by…

A: Given data:

Q: Р.3) A collar of mass m = 2 kg is constrained %3D to move in the vertical plane along a rough rod of…

A: Consider the free body diagram as shown below for the collar.

Q: The 400-kg mine car is hoisted up the incline using the cable and motor M. For a short time, the…

A: According to the given data m=400kg mg=3924N F=3500t2 v1=2m/s and s=0 at t=0 sec We need to find…

Q: The 10-lb block rests on a surface for which MUK - 0.5, it is acted upon by a radial force of 2 lb…

A: Given data :- Weight of block = 10 lb Coefficient of kinematic friction = 0.5  Radial force = 2 lb…

Q: The ball of mass m is guided along the vertical circular path r = 4cos(0)meters using the arm OA. If…

A:

Q: The cylinder with mass, m = 30 kg, and 400 mm diameter rests against the surfaces as shown in the…

A: As per the guidelines we can answer the first question only, for the other question kindly resubmit…

Q: Block A has a mass of 40 kg and block B has a mass of P-kg. The coefficient of kinetic friction…

A: SolutionGiven datamA=40kgmB=20kgμK=0.2SB=4m…

Q: Two identical 16-kg spheres are attached to the light rigid rod, which rotates in the horizontal…

A:

Q: The boy of mass 46 kg is sliding down the spiral slide at a constant speed such that his position,…

A:

Q: Determine the constant force P required to cause the 0.58-kg slider to have a speed v2 = 0.55 m/s at…

A:

Q: The simple pendulum A of mass ma = 3.9 kg and length I = 1.51 m is suspended from the trolley B of…

A: Given Data: mA=3.9 kgl=1.51 mmB=7.9 kg   To Find: Velocity of trolley B, vB.

Q: When s = 0.6 m, the spring is relaxed, and the 10 kg block, which is subjected to a force of 125 N,…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.