A concrete bored pile has a diameter of 800 mm as given in the figure below. Calculate the ultimate load carrying capacity of the pile. --0.8- Clay Cu = 60 kN/m² Y = 18 kN/m³ 4m %D G.W.T Sand $ = 30° Y = 20 kN/m³ 6m Clay

A concrete bored pile has a diameter of 800 mm as given in the figure below. Calculate the ultimate load carrying capacity of the pile. --0.8- Clay Cu = 60 kN/m² Y = 18 kN/m³ 4m %D G.W.T Sand $ = 30° Y = 20 kN/m³ 6m Clay

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.6P: Determine the maximum load that can be allowed on a 450 mm diameter driven pile shown in Figure...

See similar textbooks

Related questions

Q: 1 0.7 A group of 6 piles and a pile cap are supporting a circular m m column which has a diameter of…

Q: H.O 9 A 20-m-long concrete pile is shown in Figure below. Estimate the ultimate point load Q, by a.…

A: Given concrete pile Length=20m Size=460×460mm

Q: The wooden pile shown in the figure has a diameter of 90 mm and is subjected to a load of P = 60 kN.…

Q: A concrete pile is 20 m long has a cross section of 0.46 m × 0.46 m. The pile is embedded in a sand…

Q: Draw a flow net for the single row of sheet piles driven into a permeability layer as shown in…

Q: A square concrete pile12m long is shown in Figure. Estimate the following: Ultimate shaft carrying…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: Н.О 10 A concrete pile 20 m long having a cross section of 0.46 m x 0.46 m is fully embedded in a…

A: Given data- Saturated Clay layer. Length of concrete pile (L) = 20 m Square cross-section = 0.46 m ×…

Q: e figure has a diameter of 120 mm and is subjected to a load of P = 80 kN. Along the length of the…

Q: c. Coyle and Castello's method Use m= 600 in Eq. (12.28). Concrete pile 460 mm x 460 mm Loose sand…

A: Solution; Given that; long =20 m Concrete pile 460 mm×460 mm

Q: The group pile below is to be built in normally consolidated clay. Calculate the consolidation…

Q: A pile of diameter 457 mm is fully embedded in a clay strata as shown in figure. C- 25 kN/m y= 16…

Q: Refer to the pile shown in Figure P 9.1. Estimate the side resistance Qs bya. Using Eqs. (9.40)…

A: Coyle and Castello analyzed 24 large–scale field load tests of driven piles in sand. from the basis…

Q: Find the maximum pile capacity for the pile group shown in figure below. If My = 500 kN.m and V =…

A: Given bending moment about y axis My=500 KN.mAxial force V=1500 KNno. of piles n=9

Q: A 600 mm diameter and 25 m long driven concrete pile car- ries a column load of 1200 kN. It is…

A: The length of the pile is .The diameter of the piles is .Total column load is .Shaft resistance is…

Q: Problem 1. A 12-m-long 356-mm-diameter concrete pile is shown in Figure below. Estimate the…

A: ###Allowable Bearing Capacity of soil for pile in Cohesionless Soil###

Q: Design a reinforced concrete footing supported on piles. The column is 600 mm square and exerts a…

A: Solution: Given: fc = 28 MPa fy = 414 MPa Bearing capacity of pile = 95 kN Factored load = 800 kN…

Q: d. Starting out from the condition where the water table is above the excavation line on both sides…

A: Brief concept introduction- Sheet Pile- Sheet piles are used to support earth retention and…

Q: A driven closed-ended pile, circular in cross section, is shown in Figure P 9.4.Calculate the…

A: Given:- Irr = 50. c'=0 width =381mm To find:- a. The ultimate point load using Meyerhof’s…

Q: For the (4 x 4) pile group as shown in the figure, the settlement of pile group, in a normally…

Q: Figure below shows a precast circular pile is driven into two clay stratums to a depth of 14 m. the…

Q: A concrete pile 20 m long having a cross section of 0.46 m x 0.46 m is fully embedded in a saturated…

Q: Determine the primary consolidation settlement for the 20 m long pile group shown below. Soil…

Q: The wooden pile shown in the figure has a diameter of 95 mm and is subjected to a load of P = 80 kN.…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: • Example: 32/2 A reinforced concrete pile 30ft long and 15 inches diameter is embedded in a…

A: we have to find the net pullout capacity

Q: For the soil profile shown in figure below, the minimum number of precast concrete piles o 300 mm…

A: Given- Efficiency of pile group=100%diameter=300mmFOS=2.5It is needed to find the minimum number of…

Q: The wooden pile shown in the figure has a diameter of 100 mm and is subjected to a load of P = 70…

A: This question is related to the Strength of Material.

Q: A 20-m-long concrete pile is shown in Figure P9.1. Estimate the ultimate point load Q, by a.…

Q: The wooden pile shown in the figure has a diameter of 95 mm and is subjected to a load of P = 80 kN.…

A: Given P= 80 KN Dia of pile = 95 mm

Q: A machine foundation is supported by four prestressed concrete plies driven to bedrock. The length…

Q: Draw a flow net for the single row of sheet piles driven into a permeable layer as shown in Figure…

A: k = 4 x 10-4 cm/s or 4 x 10-6 m/s H1 = 3 m H2 = 0.5 m D = 1.5 m D1 = 3.75 m

Q: The wooden pile shown in the figure has a diameter of 105 mm and is subjected to a load of P = 70…

Q: Q1/ For the footing shown in Figure (1). estimate the pile group capacity. 0.6m dia bored pile Clay…

A: Ultimate load carrying capacity of pile: It is the maximum load which can be applied on pile without…

Q: Q1: Determine the allowable load capacity for the driven pile of 0.6 m diameter embedded in a…

A: We have to determine the value of allowable load capacity for the driven piles of 0.6 m diameter…

Q: Determine the design capacity of the concrete pile shown in Figure 3 for a factor of safety of 2. O…

Concept explainers

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.

Question

A concrete bored pile has a diameter of 800 mm as given in the figure
below. Calculate the ultimate load carrying capacity of the pile.
-0.8-
Clay
Cu = 60 kN/m²
Y = 18 kN/m³
%3D
4m
G.W.T
Sand
6m
$ = 30°
Y = 20 kN/m³
Clay
Cu = 100 kN/m²
Y = 20 kN/m³
5m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

i need the answer quickly
Problem 1. A 12-m-long 356-mm-diameter concrete pile is shown in Figure below. Estimate the allowable capacity, Qaul, of the pile. Use K = 1.3 Ko, 8' = 0.8 Ø' and a factor of safety equal to 3. 12 m Concrete pile 356 mm Loose sand $₁ = 30° y = 17.5 kN/m³ Dense sand $2 = 42° y = 18.5 kN/m³
A concrete pile 20 m long having a cross section of 0.46 m × 0.46 m is fully embedded in a saturated clay layer. For the clay, given: Yat = 18 kN/m², = 0, and Cu = 80 kN/m?. Determine the allowable load that the pile can carry (FS = 3). Use %3D the A method to estimate the skin resistance.
Redo Problem 9.23 assuming that the water table coincides with the top of the fill and that γsat(fill) = 19.8 kN/m3. If the other quantities remain the same, what would be the downward drag force on the pile? Assume ẟ' = 0.5 Φ'fill.
Figure 18.26a shows a pile. Let L = 20 m, D = 450 mm. Hf = 4m, f = 17.5 kN/m3, fill = 25. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that = 0.5 fill. FIG. 18.26 Negative skin friction
Redo Problem 12.20 using Vesics method, assuming that the skin friction is distributed uniformly along the shaft. 12.20 A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
Answer with FOUR decimal places
A pile with a diameter of 40cm and a length of 15m is intended for the sandy soil. If the standard tube test around the pile is homogeneous with N = 30, find the tip support and friction support of the pile. ans Qs=1507.2kn Qp=1130.4kn
H.Q 10 A concrete pile 20 m long having a cross section of 0.46 m x 0.46 m is fully embedded in a saturated clay layer. For the clay, given: Ysat = 18 kN/m3,0= 0, and cu = 80 kN/m2. Determine the allowable load that the pile can carry (FS = 3). Use the method to estimate the skin resistance.
A 11-in. square concrete pile is driven into a clay deposit as shown in the figure below. The unit weight of the clay soil is 100 lb/ft³. The embedded length of the pile is 40 ft. Determine the pile's design capacity (kips), using a factor of safety of 2. HINT: from Figure 10-7, with c = 1 kip/ft², a = 0.83. Design = ? 40 ft TKN7. Clay 9. = 2000 lb/ft² →B, square Round your answer to ONE decimal place
A bored pile is shown in the figure. The diameter of the pile is 60 cm. Calculate the ultimate bearing capacity of the pile. Assume Dor=20x), the pile soil motion angle, 8=0.75*8' Sand c'=0, 0-30° 10m 8=20 kN/m Clay Cu = 100kpa X=20kN/m3 5m
The section of a 3 x 4 group pile in a layered saturated clay is shown in the figure below. The piles are square in cross section (356 mm x 356 mm). The center-to-center spacing, d, of the piles is 889 mm. Determine the allowable load-bearing capacity of the pile group. Use FS = 4. Note that the groundwater table coincides with the ground surface.