A composite bar is rigidly attached to the wall at A as shown. Axial loads are applied at the positions indicated. Bronze Steel E = 83 GPa diameter = 100 mm E = 200 GPa %3D diameter = 60 mm 1200 kN 900 kN A 2.5 m- 3 m How much is the displacement at joint C? Select the correct response: 0.97 mm 0.68 mm C0.79 mm 0.86 mm

A composite bar is rigidly attached to the wall at A as shown. Axial loads are applied at the positions indicated. Bronze Steel E = 83 GPa diameter = 100 mm E = 200 GPa %3D diameter = 60 mm 1200 kN 900 kN A 2.5 m- 3 m How much is the displacement at joint C? Select the correct response: 0.97 mm 0.68 mm C0.79 mm 0.86 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two plates of which (2.5 d) and d as outer and inner diameter respectively and thickness 25 mm each are held together by means of a bolt. The bolt material S-400 N/mm² and E210000 N/mm² while plate material E= 72000 N/mm². The initial preload in the bold is 6.0 KN and force on the joint is 12 kN. Find out size of bolt assuming factor of safety 2.0.
Show the complete solution
The spring clamping force Fg = 2 N. The contact pressure force FA and the joint forces FB at the jump piece 1 should be determined for the toggle mechanism with a straight guide shown in figure. C 26 mm B 2 10 mm A 1 8 mm 7 mm D 10 mm 15 mm 10 mm
A steel rod is located by using force fit into the body of a mechanical system with a radial interference of 30 um. Considering the static loading in the figure, evaluate the factor of safety employing Von-Mises criteria. Data are as follows: E = 210 GPa, S, = 510MPA %3D d=40mm 20KN 30 30mm 60mm 50mm
The shaft is pulled by force F. Shaft The yield strength of the material is 500 MPa and the factor of safety is 2 Spindle length 1 m Size the shaft as the outer diameter / inner diameter ratio is 1.5 Note:show the calculations in detail
The spring clamping force Fg = 2 N. The contact pressure force FA and the joint forces Fg at the jump piece 1 should be determined for the toggle mechanism with a straight guide shown in figure. C 26 mm B 2 10 mm A 1 8 mm 7 mm D 10 mm 15 10 ww ww
Which set of compatibility equations matches the following torsion members connected end-to-end in series? 30 in. O || = C a 560 8₁ a & + gap 05/0 18 in. 6 in. (2) 0 & + ₂ = 0 О ф, = фг 0 8₁ = 8₂ - 8₂ 04+₂=0 & + ₂ = constant Ta (3) 8₁ + gap = 8₂ &₁ = & + gap D. & + ₂ = constant 8 in. (2)
static of rigid bodies problem
66 ll ? e V:09 The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at point B, the tube made of material with G2=230 GPa has an outer diameter 37 mm and wall thickness of 7 mm. If T1=803 N.m and T2=1445 N.m, answer the following questions: B T2 N-m 0.4 m 0.1 m D. 0.3 m T1 N-m The polar moment of inertia of the rod BD is Your answer The polar moment of inertia of the tube CA is
The steel bar shown in the picture and for loading. Assuming that both support fit perfectly before loads are applied. What are the RA response and RB response? FK=34 kN , FD=17 kN , A1=85mm^2 , A2=119 mm^2 , L1=L2=37 mm , L3=L4=57 mm ,E=200 GPa
Data: r=0.25 inch, d=0.4 pig and h=0.5 inch, wi=2.5 inch and w= 1.5 inch.The forces fluctuate between a tension of 14 Kips and a compression of 5 Kips. It is made of AISI 1018 CD. steel.The connecting element in the figure is failing. What is the most critical point and give recommendations to improve the situation.