A completely mix process is designed with the following data: Qo = 10000 m³/d, BOD after PST = 150 mg/l, effluent BOD = 5 mg/l Y = 0.5 kg/kg, Kd = 0.05 per day, MLSS = 3000 mg/l Underflow concentration (Xu) = 10000 mg/l for 2° sedimentation tank, 8c = 8 days. What should be the reactor volume in m³?

A completely mix process is designed with the following data: Qo = 10000 m³/d, BOD after PST = 150 mg/l, effluent BOD = 5 mg/l Y = 0.5 kg/kg, Kd = 0.05 per day, MLSS = 3000 mg/l Underflow concentration (Xu) = 10000 mg/l for 2° sedimentation tank, 8c = 8 days. What should be the reactor volume in m³?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The results of a water analysis for Sungai Buaya is shown below: = 2.5 meq/L Mg²* = 0.6 meq/L Na* 1.7 meq/L SO? = 2.0 meq/L 0.2 meq/L Ca²+ HCO; %3D 2+7 = 0.4 meq/L = 0.4 meq/L Cl K+ (i) Calculate the concentration for each cation and anion component in mg/L (ii) Draw a miliequivalent per litre bar graph (iii) List the hypothetical combinations with values (iv) Calculate the non-carbonate hardness in mg/L as CaCO3
Two wastewater streams A and B, having an identical ultimate BOD are getting mixed to form the stream C. The temperature of the stream A is 20 °C and the temperature of the stream C is 10 °C. It is given that • The 5-day BOD of the stream A measured at 20 °C=50 mg/l • BOD rate constant (base 10) at 20 °C-0.115 per day Temperature coefficient = 1.135 The 5-day BOD (in mg/l, up to one decimal place) of the stream C, calculated at 10 °C, is ●
Water treatment plant : SOR = 0.35 mm/sec; The analysis of this water found that there are 6 different particle sizes: 0.1 mm with settling velocity of 0.2 mm/sec; and percentage of particles = 10 %; 0.2 mm with settling velocity of 0.25 mm/sec; and percentage of particles = 20 %; 0.3 mm with settling velocity of 0.3 mm/sec; and percentage of particles = 15 %; 0.4 mm with settling velocity of 0.35 mm/sec; and percentage of particles = 5 %; 0.5 mm with settling velocity of 0.4 mm/sec; and percentage of particles = 30 %; 0.6 mm with settling velocity of 0.5 mm/sec; and percentage of particles = 20 %; Calculate the efficiency of this tank ?
1
The influent suspended solids concentration to a primary settling (clarifier) tank is 300 mg/L. The average flow rate is 0.037 m3/s. If the suspended solids removal efficiency is 65 percent, how many kilograms of suspended solids are removed in the primary settling tank each day?
A waste sludge flow of 40 m³/day is gravity thickened in a circular tank with a diameter of 6.8 m. The solids concentration is increased from 4.5% to 7.5% with 85% suspended- solids capture. Calculate the solids loading in kg/m² d and the quantity of thickened sludge in m³/d.
Settling tank has a depth of 3 m and surface area of 900 m2 is used to remove particles of size 0.01 mm and specific gravity 2.65. Compute the removal percentage of the tank for the discharge of 8000 m3/d. Take viscosity of water equal to 10-3 kg/m.s.
Please give me both a and b solutions A settling tank with (L=6m, W=4 m , H= 4 m) treats a waste stream (60,000 l/min) and removes suspended solids with 200 micrometer diameter that have a settling velocity of 0.04 m/s. a. What is the removal efficiency of his tank? b. If a 100% removal efficiency is to be achieved, How long should the settling tank be?
The 750-bed Associated Center of Medical Excellence (ACME) Hospital has a small activated sludge plant to treat its wastewater. The average daily Medical Center discharge is 1,250 L per day per bed, and the average soluble BOD5 after primary settling is 450 mg/L. The aeration tank has effective liquid dimensions of 10.0 m wide by 25.0 m long by 3.5 m deep. The plant operating parameters are as follows: MLVSS = 2,750 mg/L MLSS = 1.25 (MLVSS) Settled sludge volume after 30 min = 250 mL/LDetermine the following: aeration period, F/M ratio, SVI, solids concentration in return sludge.
1. The following information is provided for an activated sludge system design: Parameter Symbol Value Units Flow rate Q 10000 m³/d Influent BOD So 150 mg/L Effluent BOD S 2 mg/L Hydraulic residence time Ꮎ 4 hr Mean cell residence time Oc 6 d Maximum specific growth rate μm 3 1/d Half saturation constant Ks 40 mg/L Yield coefficient Y 0.5 Endogenous decay coefficient b 0.08 1/d Death rate coefficient γ 0.04 1/d Determine: a) The aeration tank biomass concentration (X) in mg/L b) The aeration tank oxygen requirement in kg/d c) The rate of biomass wasting in kg/d
Gave wrong values earlier. These are the correct values A settling tank having a depth of 3.5 m and surface area of 1000 m2 is used to remove particles of size 0.01 mm and specific gravity of 2.6. Calculate the removal percentage of the tank for the discharge of 7000 m3/d. Take viscosity of water as 1.1x10-3 kg/m.s.
A complete-mixed activated sludge process (CMAS) is to be designed to treat 6.0 MGD of primary effluent having a BOD5 of 190 mg/L. The requirement is that the effluent BOD5 and TSS concentrations be 20 mg/L or less on an annual average basis. The following biokinetic coefficient obtained at 15°C: Y = 0.6 mg VSS/mg BOD5, k = 2.85 d-1, Ks = 70 mg/L BOD5, and kd = 0.041 d-1. Assume that the MLVSS concentration in the aeration basin is maintained at 2,500 mg/L. Determine: a. The minimum MCRT (d) b. The MCRT necessary to meet the requirement (d) c. The volume of the aeration basin (ft3)