Answered: A communications company is laying… | bartleby

Related questions

Question

A communications company is laying cable underground between 2 subdivisions, A and B, on opposite sides of a river which is 150 metres wide. Subdivision B is 1400 m downstream from A and on the opposite bank. It costs $50/m to lay cable underground and $130/m to lay cable
underwater. What is the least costly way to lay cable?

Expert Solution

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

ou have a summer job as an assistant technician for a telephone company in California.During a recent earthquake, a 1.0-mile long underground telephone line is crushed atsome point. This telephone line is made up of two parallel copper wires of the samediameter and same length, which are normally not connected. At the place where theline is crushed, the two wires make contact. Your boss wants you to find this placeso that the wire can be dug up and fixed. You disconnect the line from the telephonesystem by disconnecting both wires of the line at both ends. You then go to one end ofthe line and connect one terminal of a 6.0-V battery to one wire, and the other terminalof the battery to one terminal of an ammeter. When the other terminal of the ammeteris connected to the other wire, the ammeter shows that the current through the wire is1.0 A. You then disconnect everything and travel to the other end of the telephone line,where you repeat the process and find a current of 1/3 A.
A metal has mass of 8 kg when the mental is hanging from a spring scale and the totally submerged in water, the scale needs 3.30kg. What is the density of the mental? (water density=1000kg/m^3) (A)2.80x10^3kg/m^3 (B)5.80x10^3kg/m^3 (C)1.70x10^3kg/m^3 (D)3.30x10^3kg/m^3
A scale is used to measure the weight of an object and it is 5.37 N. When the object is fully immersed in water, the scale reads only 3.43 N. What is the density of the object?
Part (a) Find the direction of the force for wire A in degrees. Measure this angle counterclockwise, in degrees, from the positive x-axis. θA = ______ Part (b) Find the direction of the force for wire B, in degrees. Measure this angle counterclockwise, in degrees, from the positive x-axis. θB = ______ Part (c) Find the direction of the force for wire C, in degrees. Measure this angle counterclockwise, in degrees, from the positive x-axis. θC = ______
The Mariana trench is located in the Pacific Ocean at a depth of about 11000 m below the surface of the water. The density of seawater is 1025 kg/m3. (a) If an underwater vehicle were to explore such a depth, what force would the water exert on the vehicle's observation window (radius=0.276 m) ? Answer:- (a) Number____Units____ (b) For comparison, determine the weight of a jetliner whose mass is 8.22×105 kg. Answer:-- (b) Number_____ Units_____
A hypodermic needle is 2.76 cm in length and 0.39 mm in diameter. What pressure difference between the input and output of the needle is required so that the flow rate of water through it will be 1 g/s? (Use 1.0 ✕ 10−3 Pa · s as the viscosity of water.)
Water flows through a pipe with increasing cross-sectional area. Which one of the following statements is true? The speed of the water decreases, while its pressure increases The speed of the water decreases, while its pressure remains constant The speed of the water decreases, while its pressure decreases The speed of the water remains constant, while its pressure increases
A cube of compressible material (such as Styrofoam or balsa wood) has a density ρ and sides of length L. a)If you keep its mass the same, but compress each side to 0.333 of its length, what will be its new density, in terms of ρ? b)If you keep the mass and shape the same, what would the length of each side have to be (in terms of L) so that the density of the cube was 5.00 times its original value?