A column with circular cross section of 30 mm diameter has its both ends fixed and is subjected to an axial compressive load. Determine minimum length of column for which Euler's formula can be applied. Take oc = 300 MPa and E = 200 GPa for the material of column O a. 1.216 m O b. 1216.7 m O c. 1.216 mm

A column with circular cross section of 30 mm diameter has its both ends fixed and is subjected to an axial compressive load. Determine minimum length of column for which Euler's formula can be applied. Take oc = 300 MPa and E = 200 GPa for the material of column O a. 1.216 m O b. 1216.7 m O c. 1.216 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rigid bar AB of length L = 1600 mm is hinged to a support at A and supported by two vertical wires attached at points C and D such that AC = 500mm and AD = 1200mm Both the wires have same cross sectional area of 16 mm² and made of the same material having Young's modulus of 200 GPa. The wire at C has a length of 400 mm and that at D has 800 mm. Determine the tensile stresses in the wires and downward displacement at point B of the bar when a load of 1 kN is suspended at B.
A slightly tapered bar AB of solid circularcross section and length L is supported at end B andsubjected to a tensile load P at the free end A. Thediameters of the bar at ends A and B are dA and dB,respectively. Determine the length of the bar if theelongation of the bar due to the load P = 45 kipsis 0.02 in. Assume that E = 10,400 ksi.
ts. 5. Two C310×45 channels are latticed together so they have equal moments of inertia about the principal axes. Determine the minimum length of column having this section, assuming pinned ends, E = 200 GPa, and a Answer.#6 proportional limit of 240 MPa. What safe load will the column carry for the length of 12 m with a factor of safety of 2.5? For C310x45, take I = 67.3×106 mª 6. Repeat problem 5 assuming that one end is fixed and the other hinged. Ans L = 9.89 m, F = 738 kN
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 13 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 22 ksi, determine the minimum diameter d₁ required for rod (1). A (2) d₁ F₂ B C O 1.087 in. O 0.823 in. O 0.541 in. O 0.867 in. O 1.003 in. d₂
PLEASE ANSWER NUMBER 8.MECH 311(MECHANICS OD DEFORMABLE BODIES): PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
Situation 2 - A steel column of hollow circular cross section is supported on a circular steel base plate and a concrete pedestal as shown in Figure M52-178.3. The column has outside diameter d = 250 mm and supports a load P = 800 kN. 28. Determine the minimum required thickness (in mm) if the allowable stress in the column is 55 MPa. A. 20.1 В. 22.4 29. Determine the minimum required diameter D (in mm) of the base plate if the allowable bearing stress on the concrete pedestal is 11.5 MPa. А. 312 В. 275 30. Determine the thickness (in mm) of the base plate if the allowable shearing stress in the base plate is 160 MPa. А. 9.3 В. 8.6 С. 18.2 D. 19.3 -D Figure M52-178.3 С. 254 D. 298 C. 6.4 D. 7.2
Members BC and DE are 50 mm wide and 16 mm thick and made of steel (E = 200 GPa). Member AF is rigid. For a load of P = 60 kN, determine 500 mm (a) the normal stress in member BC, В C (b) the normal stress in member DE, 250 mm E (c) the displacement of point A. D Assume BC and DE do not yield or buckle. 250 mm F 500 mm- 650 mm
A 13-mm-diameter steel (E = 193 GPa) rod (2) is connected to a 27-mm-wide by 10-mm-thick rectangular aluminum (E = 72 GPa) bar (1), as shown. Assume L1 = 0.74 m and L2 = 1.38 m. Determine the force P (in kN rounded to the nearest tenths) required to stretch the assembly 8.1 mm.
A rectangular steel plate with a thickness h of 5 mm is shown below. All four edges are fixed. An uniform pressure of 20 MPa is applied on the top face of the plate. (Use E=210GPa and v=0.3) 1200 mm Please determine: 1) the maximum stress in the plate; and 2) the maximum deflection in the plate. 600 mm
The rigid bar ABC is supported by pin at A and aluminium wire BD, is horizontal before the Load P is applied. Find the vertical displacement of point C caused by the load P=35 KN. Where E = 70 GPa and the area of the wire is 200 mm?. D. 300 mm B 400 mm- 200 mm
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 8 mm². The cross-sectional area of rod (2) is 17 mm². For a uniformly distributed load of w = 2.8 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 4.20 m. (1) B Answer: a = i L W E 2
Consider a deformable homogenous slender rod of constant area along its length. It is axially loaded at points A and C. According to Saint-Venant's Principle, which of the following point(s) is/are the actual maximum axial stress underestimated the most by the average stress? A B. F F L