A column section b = 400 mm, h = 600 mm is reinforced with longitudinal bars Ast = 12-ϕ20 mm equally distributed along all faces. Lateral ties are composed of 12 mm rectangular hoops with clear cover equal to 40 mm and 12 mm cross ties in both directions. Concrete yield strength f’c = 27 MPa and steel yield strength, fy = 415 MPa. Calculate the nominal axial strength of the column in kN

A column section b = 400 mm, h = 600 mm is reinforced with longitudinal bars Ast = 12-ϕ20 mm equally distributed along all faces. Lateral ties are composed of 12 mm rectangular hoops with clear cover equal to 40 mm and 12 mm cross ties in both directions. Concrete yield strength f’c = 27 MPa and steel yield strength, fy = 415 MPa. Calculate the nominal axial strength of the column in kN

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.2.1P: A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The...

See similar textbooks

Similar questions

Situation #2 A concrete co lumn has a diameter 4 300 mm. The column has 6 6teel rinforcing bars. Each renforcing bar has a crocs-sectiomal area 4 J0o mm2. The column is I150m lorg and has a load 17 1,370 kn applied to a igid steel plati af the top y the column. The plati distributes the load evenly over the 4 the co lumn.) tumn) top E,- 300 GPa ard Ec=arGPa Find the sfress in the &feel ard in the concrete ard the defomation urder the load.
Assume Grade 50 steel and use f. = 5,000 psi for parts (a) thru (b). (a) u The beam below is subjected to a factored moment M₁ = 800 ft-k. Assuming that the reinforcement is to be placed in two layers as shown, design the reinforcement. (b) Calculate the moment strength oM₁ of your design in part (b) and compare that with the factored moment M₁ = 800 ft-k. Is your design adequate? Be sure to check the strain in the tension steel. A k 6" 4" 6" ....... 4" 12" 8" 4" 4"! 32"
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
Q₁:Design a concrete column shown in figure using fe-28 MPa, fy- 420 MPa, ultimate applied load. P=545 KN B E 1500 P=350 KN b Section (a-a)
Details of a rectangular column are as follows: Column width along X-axis-250 mm Column Depth along the Y-axis-600 mm 8-25 mm diameter bars distributed equally along the longer sides. 10 mm diameter ties spaced at 10 mm on centers Concrete 28th day Compressive strength, fc;=20.7 MPa Reinforcing Steel yield strength, fy-415 MPa Assume that compression steel yields. a) Which of the following gives the nominal balanced load Pb (kN). A = 90.4 mm b) Which of the following gives the nominal axial load (kN) that the column n carry at an eccentricity of 200 mm along the X axis from the centroidal Y-axis.
Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown. Design shear reinforcement of prestressed beam with the following properties listed. Properties: f^c=28 MPa fy = 276MPa Aps = 800 mm² Ds = 10mm Dm = 18mm fse = 800 MPa fpu = 1500 MPa fpe = 860 MPa Pe = 250kN
Find the maximum allowable value of P for the column. The cross-sectional areas and working stresses (ow) are shown in the figure. |2P Steel: A = 500 mm2 Ow = 120 MPa P Timber: 4P A = 2000 mm? Ow = 12 MPa Concrete: A = 8000 mm? O = 16 MPa
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
Compute the co-ordinates for (Pnb, Mnb) and (Pub, Mub) for rectangular columns using h=24in b=14in Effective cover =3in. Reinforcement consists of 4-#9 bars on each side (totla of 8 bars) f'c=7000 psi fy=40000 psi. Use a yield strain of 0.004 for steel.
Subject is reinforced concrete design show all steps
3. A reinforced rectangular concrete beam having a width of 300 mm, effective depth of500 mm, fc’ = 24 MPa, fy = 415 MPa, 4 - 28 mmɸ, d’ = 65 mm. Present the following (a) actual steel ratio (b) maximum steel ratio (c) a(d) c (e) check if steel yields (f) ?steel(g) type of failure (h) reduction factor (i) moment capacity
Calculate the design moment strength for the reinforced concrete beam section shown below. f. = 24 MPa and f, = 415 MPa . 300 mm 5-D28 50 mm di = 812.5 mm