A close-coiled helical spring of 10 active turns is made of 8 mm diameter steel wire. The mean coil diameter is 10 cm. If G = 80 GPa for the material of spring, the extension of spring under a tensile load of 200 N will be nearly 1.40 mm 2. 45 mm 3. 49 mm 4. 53 mm

A close-coiled helical spring of 10 active turns is made of 8 mm diameter steel wire. The mean coil diameter is 10 cm. If G = 80 GPa for the material of spring, the extension of spring under a tensile load of 200 N will be nearly 1.40 mm 2. 45 mm 3. 49 mm 4. 53 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The assembly shown in figure below consists of a light rigid bar AB, pinned at O, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is touch to its support. A 0.75 m Steel A = 250 mm E = 200 GPa *i* O 1.5 m Aluminum L = 2m A = 300 mm' E = 70 GPa B D
1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
1) The head H is connected to the cylinder of a compressor using six steel bolts. If the clamping force in each bolt is 4000N, determine the normal strain in the bolts. Each bolt has a diameter of 5 mm. If o₂ = 280 MPa and Est = 210GPa, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released? a) 0.970 b) 0.203 c) 0.970(10-³) d) Insufficient information to determine because the stress is beyond yield point H &
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. А) 12500-pi в) 6250*pi с) 3125*pi D) 1563*pi
A 5.2-m-long aluminum tube (1) is to be connected to a 2.2-m-long bronze pipe (2) at B. When put in place, however, a gap of 9 mm exists between the two members, as shown. Aluminum tube (1) has an elastic modulus of 69 GPa and a cross-sectional area of 1980 mm2. Bronze pipe (2) has an elastic modulus of 93 GPa and a cross-sectional area of 3970 mm2. If bolts are inserted in the flanges and tightened so that the gap at B is closed, determine: (a) the normal stresses ?1, ?2 produced in each of the members. (b) the displacement (change in length of material (2), up is positive) uB of flange B with respect to support A. 5.2 m 2.2 m Answers: (a) 0₁ = (b) Ug = C (1) B (2) -95.40 1.126 9 mm MPa, 0₂ = mm. -47.58 MPa
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
3) The rigid horizontal bar AB is supported by three vertical rods as shown in the figure and carries the load of 110 kN. The system is stress free before the load is applied. After the load was applied, the temperature of all wires is raised by 20°C. Use a = 12x10-6/°C for steel, a = 18x10-6/°C for copper and a = 20x10-6/°C for brass. Neglecting the weight of the bar AB, determine the location of the 110 kN force in order that AB remains horizontal. copper bar: A=195mm? steel bar: brass bar: A=130mm? A=325mm? A C B 110 kN 3.00m 2.00m 1.80m _ 1.20m 1.50m
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 102 GPa] with a cross-sectional area of A₁ = 200 mm². Bar (2) is an aluminum alloy [E = 72 GPa] with a cross-sectional area of A₂ = 640 mm². All bars are unstressed before the load P is applied; however, there is a 2-mm clearance in the pin connection at A. Assume L₁ = 1880 mm, a = 1060 mm, b = 620 mm, c = 480 mm, and L₂ = 1270 mm. If a load of P = 71 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. (1) L₁ b tc B (2) D L2
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 94 GPa] with a cross-sectional area of A₁ = 280 mm2. Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A2 = 590 mm². All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L₁ = 1840 mm, a = 880 mm, b = 540 mm, c = 430 mm, and L₂ = 1340 mm. If a load of P = 87 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. h (1) L₁ b a BI Answers: C (2) D L2
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 95 GPa] with a cross-sectional area of A1 = 260 mm2. Bar (2) is an aluminum alloy [E = 69 GPa] with a cross-sectional area of A2 = 690 mm2. All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L1 = 2000 mm, a = 1080 mm, b = 610 mm, c = 460 mm, and L2 = 1380 mm. If a load of P = 100 kN is applied at B, determine(a) the normal stresses in both bars (1) and (2).(b) the downward deflection of point A on the rigid bar.
1. An axial force of 250 kN is applied to the assembly shown, made of cylindrical brass core surrounded by an aluminum shell. The axial force is applied through rigid end plates. a) Determine the normal stress in each of the metal components, given that Ebrass = 105 GPa and Ealum = 70 GPA. 100mm b) What is the axial deformation of the assembly? 200mm 200mm
Problem 3: Inside a steel tube, 2.4 meters long, 34 mm radius, and 1.5 mm thick, 32.5A circular bar made of aluminum with a radius of mm is inserted and these two materials arethey are linked together to form a cross section that will work. This cantilever beam obtained from end Ait is fixedly supported. This cantilever beam,A torque of T = 900 Nm from end B(torque) is applied. Stiffness modulus of steel, Strength= 77 GPa and the stiffness modulus of aluminum Gal = 26Since GPa is the rotation at point BWhat is the (torsion) angle? Calculate.