A close coiled helical spring is made of 1omm diametes Steel sod, the coils having io complete tums amd amcan diametes of Somm. calulate he increase in the number of tums and the bending Stress induced in the Section, if it axial Couple of lONmiAlso, calaulate the Subjected to an Horsional stiffness of the Spring Take E: 21X1SN

A close coiled helical spring is made of 1omm diametes Steel sod, the coils having io complete tums amd amcan diametes of Somm. calulate he increase in the number of tums and the bending Stress induced in the Section, if it axial Couple of lONmiAlso, calaulate the Subjected to an Horsional stiffness of the Spring Take E: 21X1SN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

B4 The short concrete cylinder having a diameter of 50 mm is subjected to a torque of 500 Nm and an axial tensile force of 2 kN. Find: 500 Nm 500 Nm A 2kN 2kN (a) the tensile stress in the concrete;
The specifications for a coil spring are known. Infinite fatigue life is required, using a safety factor of 1.3 applied to the maximum load only. The fatigue strength can be represented by a line between τmax= 600, τmin= 0 and τmax= τmin= 900 MPa.Assume both end plates are in contact with nearly a full turn of wireand that the end plate loads coincide with the spring axis.Determine a suitable combination of d, D, and N, if C = 8
A homogeneo us 4o kg vigid block is suspended by three spring whose lower ends were oviginally at the same level Each steel spring has 30 tums •f meau diametu of loo mm 8 mm diameter wive on a G= 83 GN/m?.The bvonze spring has uo tuvns mean diameter of of 15 mm diameter wive on 120mm G=42 GN /m? Compute the maximun and sheaving stress in each spring Phosphor Bronze Steel Steel 1 m 2 m wwww
A hollow circular shaft of inner radius 10mm, outer radius 20mm and length 1m is to be used as a torsional spring. If the shear modulus of the material of the shaft is 150 GPa, Calculate the torsional stiffness of the shaft (in kN-m/rad).
The shows a system of turee bars ecwh made of deffereut figure muterials, aud conuected togetuer aud tue teuperature is luitiaily kept at 12°C. Thereapter, tue teuperature of tue system was raused to 50°C Ast = 200mm ABR= 450Mm A cu= 515 mm copper Brass steel 300mm 200mm Est = 200 GPa Xst = 12X10 Ecuz120 GPa EBR=100GPL XBR= 21 X10°C Lus 17x10-/°C (a-2). Determine tue thermal stress raising in each bar Ftue assembly is placed befween fwo regid wals. (2-2) Oetenuur the Foree exerted ou tue rignt right proveded betueen tue lept eud support 4 au allowanee of o,Os mum is aud leet wail . oF tue steel bar
Figure 1 shows a composite shaft ABCD acted upon horizontal forces. The moduli of elasticity and the cross-section areas of the segments of the shaft are also provided. Eal 70 GPa E = 126 GPa E = 200 GPa AAR=58 mm² ABC 77 mm2 Acp = 39 mm² Сopper 20KN 8 kN Aluminum Steel 7 kN B 20KN A 8 kN 450 mm -300 mm -- 400 mm Figure 1: Axially loaded composite shaft 2.1. Construct the diagram of internal normal forces for each cross-section of the (6) shaft (3) 2.2. Calculate the displacement of the point C with respect to the fixed-point A 2.3. If the shaft must have one uniform diameter determine the required minimum diameter of the shaft if the normal yield stress in the composite shaft must not (11) exceed 450 MPa with a factor of safety equal to 1.8.
A hard-drawn steel wire extension spring has a spring index Of 7.5, hook radii of r = 0.106 in and r2 0.089 in, and an initial tension of 1.5 lbf. The number of body turns is 13.5 and the uncorrected initial stress is 16.5 kpsi. From the given information: (a) Determine the physical parameters of the spring. (b) Find all stresses at ends A and B and the body torsion under the static load of 6 Ibf.
A helical compression spring is made with oil-tempered wire of diameter 0.2", mean coil diameter of 2", 12 total coils, 5" free length, and squared ends. (a) Find the solid length. (b) Find the force required to compress the spring to closure? (c) Find the factor of safety against yield when compressed to the solid length. (Hint: Uses Say= 0.5 Sut for shear strength.)
For Hibiscus and Rose Groups A steel helical spring is wound from No. 14 music wire with a mean helix diameter of 0.6 in. The load varies continuously between 10 and 4 Ib. Find the factor of safety.