A circular steel rod AB of diameter d, length, Modulus of elasticity E and modulus of rigidity G, is loaded as shown in figure . A rigid bar BC of length b is rigidly fixed to AB at B such that BC is perpendicular lies in the horizontal plane. Find the deflection of point C to AB and due to (1) bending of AB (ii) torsion of AB (iii) combing bending and torsion

A circular steel rod AB of diameter d, length, Modulus of elasticity E and modulus of rigidity G, is loaded as shown in figure . A rigid bar BC of length b is rigidly fixed to AB at B such that BC is perpendicular lies in the horizontal plane. Find the deflection of point C to AB and due to (1) bending of AB (ii) torsion of AB (iii) combing bending and torsion

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

There is a beam as shown in the figure below, and the flexural stiffness of the beam section is constant EI:(a) Try the Moment-area Method to obtain the slope of point A after deformation.(b) Same as the above question, try to find the slope of point B after deformation.(c) Same as the question above, try to find the vertical deflection of point C (Deflection).
Give me all solutions
The cantilever beam has a steel cable of circular cross-section area at the end. What is the area of the cable’s cross section area if there is no observed deflection at point B? The modulus of elasticity of both beam and cable is 200GPa, and the beam is a steel section with I = 120 x 106 mm4 (Hint: recall axial deformations) USE THE DOUBLE INTEGRATION METHOD.
A light uniform beam of flexural rigidity EI is simply supported at A and D. A uniform load at P per unit length is applied to AB
A simple beam is subjected to two concentrated loads as shown. The beam section is a rectangular one, A = b×h and k = 1.2.Parameters G, E, I, M, V, and A. Please find a. The strain energy (ub and us) of the deformed beam under the applied loads. The strain energy ub due to bending and another one us due to shear. b.The deflection at mid-span due to bending and shear.
A beam of flexural rigidity EI is fixed at A and supported by a linear EI at B. Determine the compressive force spring of stiffness k= developed in the spring, when the beam is subjected to a UDL of w per unit length. w A B L -
The cross-sectional dimensions of a beam are shown. Assume b-2.5 in., t-tw-0.25 in. and d=4.25 in. (a) If the bending stress at point K is 2560 psi (T), determine the internal bending moment M₂ acting about the z centroidal axis of the beam. (b) Determine the bending stress o H K Answers: (a) M₂ = (b) σH = bf i i tw at point H (positive if tension, negative if compression). lb-ft. psi.
The A-36 steel beam has a depth of 10 in. and is subjected to a constant moment M0, which causes the stress at the outer fibers to become sY = 36 ksi. Determine the radius of curvature of the beam and the beam’s maximumslope and deflection.
The cross-sectional dimensions of a beam are shown. Assume b=2.5 in., t-tw-0.375 in. and d=3 in. (a) If the bending stress at point K is 2720 psi (T), determine the internal bending moment M₂ acting about the z centroidal axis of the beam. (b) Determine the bending stress o at point H (positive if tension, negative if compression). H K Answers: (a) M₂= i (b) oH = i tw lb-ft. psi.
3. The beam ABCD is fixed with simple support of B and C as shown in the figure below. When point A is 15 mm and point D is bent upward by 10 mm, find the loads P, Q to make point A and D equal to point B and C support points. P is acting on point A, and Q is acting on point D. The Flexible Rigidity tee is 2.5 X 106 Nm (Use Maucalay's method) 15 mm B -2.5 m تے 5m 25m 25m 10 mm
A truss is subjected to loads as shown. Assume AE is constant and use virtual work method for deflection of truss. 4m 120 KN B A TINT 3m EA = constant E = 200 G Pa 2 A = 1,500 mm Find the vertical deflection at B in mm
Determine the force in members BC, GA, and BG of the truss shown in the figure below. Let P = 175 kN. NOTE: If your answer is a compressive force then just put a negative sign. If your answer is a tensile force then just type the answer directly. (ALSO, DON'T FORGET THE UNITS) 2P 2P 30 60V60° 60°V60° C 30 D 3P 4m 4m 4m Solve the force in member BC. Solve the force in member GA. Solve the force in member BG.