EXAMPLE 4.2The rigid bar BDE is supported by two links AB and CD. Link AB is madeof aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm²; linkCD is made of steel (E = 200 GPa) and has a cross-sectional area of600 mm?. For the 30-kN force shown, determine the deflection (a) of B,(b) of D, (c) of E.%3D0.4 m0.3 m30 kNDE-0.4 m0.2 m

As given in the question :- Aluminium E = 70 GPa A aluminium = 500 mm2 Steel E = 200 GPa Asteel=…

The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm; link CD is made of steel (E 600 mm. For the 30-kN force shown, determine the deflection (a) of B, (b) of D, (c) of E. 200 GPa) and has a cross-sectional area of %3D 30 kN 0.4 m 0.3 m B E -0.4 m 0.2 m

The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm; link CD is made of steel (E 600 mm. For the 30-kN force shown, determine the deflection (a) of B, (b) of D, (c) of E. 200 GPa) and has a cross-sectional area of %3D 30 kN 0.4 m 0.3 m B E -0.4 m 0.2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The strain energy stored in a prismatic member due to a transverse shear force Vy is given by 2 kyVy² U = dx 2GA Where ky is a cross-sectional shape factor given by 2 A Qz' ky .dA tz² Obtain the ky values for the rectangular, (ii) circular, and (iii) equilateral triangular cross sections.
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h= 430 mm tw= 12 mm d= 110 mm t= 9.6 mm Additionallv: • The area of each pipe is A = 3028 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is I>= 320410000 mm4. If the beam will be subiected to a shear force of V = 110 kN, determine the shear stress at point K, located at yK = 70 mm below the z centroidal axis.
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X
Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that E, = 200 GPa and Eb = 105 GPa, determine the deflection of point C. Sc A um →>> Dimensions in mm 120 180130- Steel B 65 KN 40-mm diam. D Brass 120 E 50 KN 30-mm diam.
For the beam shown below, the ratio of stiffness coefficients k41 and k43 is Assume El is constant. -2m- B 4 3m 2
The two bars are made of polystyrene, which has the stress-strain diagram shown. If the cross-sectional area of bar AB is 975 mm² and BC is 2600 mm², determine the largest force P that can be supported before any member ruptures. Assume that buckling does not occur. Include complete steps with explanations and FBD. 1m baxilno σ (MPa) 175 140 105 70 A 35ptension 0 0.20 -1.2 m P 0.40 compression B 0.60 0.80 € (mm/mm)
For the truss shown in the figure, Members AB, BC, CD, & AD have a cross-sectional area of 3 in2. Member BD have has a cross-sectional area of 4 in2. Modulus Elasticity for all members is 29 million pounds per square inch. If the value of P1 is 40 kips and P2 is 20 kips, determine the vertical deflection at B (in) and horizontal deflection at D (in). Put a negative sign if the reaction is downward or left direction.
A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place, however, a gap of A = 0.35 in. exists between the two pipes. Bronze pipe (1) has an elastic modulus of E1 = 16,000 ksi, a cross-sectional area of A1 = 2.66 in.?, and a length of L1 = 6.7 ft. Aluminum alloy pipe (2) has an elastic modulus of E2 = 10,000 ksi, a cross-sectional area of A2 = 1.37 in.2, and a length of L2 = 10.2 ft. If bolts are inserted in the flanges and tightened so that the gap at B is closed, determine: (a) the normal stresses produced in each of the members. (b) the final position of flange B with respect to support A. L2 В (1) Answer: (a) 01 = ksi 02 = ksi (b) ÕB/A = in.
А L B 425 mm C 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs). b) Determine the final width and thickness of the Aluminum bar. (1) Your Answer:
3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and cross-sectional area of 22.5 mm?. Member (2) is a short aluminum of initial length 50 mm and cross-sectional area of 40 mm?. The modulus of elasticity of the steel wire is 200 GPa and the aluminum block is 70 GPa. a) Draw the deflected shape of the rigid member and clearly label the deformation of members (1) and (2). b) Write the equilibrium and compatibility equations needed to solve the problem along with the supporting sketches. Hint: Be sure to carefully consider if the members are elongating or shortening; this must be represented mathematically. c) Calculate the internal forces in both axial members and clearly indicate tension or compression. [Ans. to Check: F2 = 535 N]
Experts Pleae help ASAP