Beam AB is made of three plates glued together and is subjected, in its plane of symmetry, to the loadingshown. Knowing that the shear force is V=3.5kN and I=8.63*106 m“, determine the following:-100 mm20 mm-Joint a80 mmC20 mm -68.3 mm20 mm60 mmThe value of Q is equal to in m3:The value of t for the Joint a is equal to in mm:The average shearing stress at Joint a is equal to in kPa:

V = 3.5 KN = 3.5 ×10³ N I = 8.63 × 10-6 m4 Solution attached below

Beam AB is made of three plates glued together and is subjected, in its plane of symmetry, to the loading shown. Knowing that the shear force is V=3.5kN and I=8.63*10® m*, determine the following: 100 mm 20 mm - Joint a 80 mm 20 mm 68.3 mm 20 mm 60 mm The value of Q is equal to in m³: The value of t for the Joint a is equal to in mm: The average shearing stress at Joint a is equal to in kPa:

Beam AB is made of three plates glued together and is subjected, in its plane of symmetry, to the loading shown. Knowing that the shear force is V=3.5kN and I=8.6310® m, determine the following: 100 mm 20 mm - Joint a 80 mm 20 mm 68.3 mm 20 mm 60 mm The value of Q is equal to in m³: The value of t for the Joint a is equal to in mm: The average shearing stress at Joint a is equal to in kPa:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please write legibly. Box the final answers and round it off to 3 decimal places.
The stress at a point is shown on the element. Determine (a) principal stress, (b) maximum in-plane shear stress. Specify the orientation of the element in each case. Find also the (c) the stress in the element if it is inclined 55° counterclockwise. (See required values in answer sheet format) 65 MPa 35 MPa 85 MPa 85 MPa 65 MPa
The figure above is a skycam which is supported by 2 wires (assume that no wires holding at the top of this device). Assume that the wires are 0.05 inches diameter. If the skycam weighs 77 lbs, then the tensile stresses of wire 1 and wire 2 are Blank 1 ksi and Blank 2 ksi respectively. SN= 77
Using an Permissible stress of 155 MPa, determine the maximum bending moment M that can be applied to the wide-flange beam shown in the figure
The figure shows a single acting rivet connecting steel plates. Rivet diameter d = 22 mm,plate thicknesses are t1 = 20 mm, t2 = 12 mm, plate width b = 100 mm and e = 38 mm. The shear strength in the material is τem = 100 MPa, the safety stress in pressure and tension is σL = 280 MPa andSince σem = 140 MPa, determine the maximum force P that the joint can safely carry.
show your solution.
2)For the supporting frame shown below: a) Determine the internal forces acting at section a-a. b) Determine the stress components that act at points A and B. IN = 2.6525x10-7 mª -300 mm 150 mm 2.5 kN a 12 mm 6 mm 6 mm 6 mm 36 mm'36 mm Section a – a
number 4 only
Show complete and neat solution
A=5, B=3, C=8 AB=53 BC=38, CB=83 CA=85
Find OF g, C, I, A', ğ,b the value A' = area above = the distance from the center oF A to the centroidal axis moment Iner tia OF base the centroidal axis OF are a above attached tロ C = the distance From tne center to the topmost Fiber OF the bcam Formulas: Fb= Mc エ Ib Fb=bending stress v: shearing stress M = ma x value OF moment OF shear : E ay AT o. 0amm O.004mm 0.02mm 0.12 m m
Given the following technical description, determine if the traverse is closed. If not, balance the traverse using TRANSIT rule and provide the Adjusted Departure. (Strictly round off to 3 dec places) Course Distance Latitude Departure Correction Adj. Departure AB 59.678 -28.67 52.34 BC 97.025 -71.23 65.88 CD 65.988 30.32 -58.61 DA 105.93 77.82 -71.87 EE-EW Sum of Adj Dep: Sum