A circular shaft of diameter D, groove diameter d, and groove radius r is subjected to a fully reversed torque T = 100 reversed moment M = 2000 lb-in. Find the factor of safety of the shaft for infinite lifetime using the modified Goodm shaft is made from steel (Sut = 85 ksi, Se = 45 ksi). Given: D = 2 in, d = 1 in, r = 0.5 in. Assume all fatigue stress concent equal to 1. M

A circular shaft of diameter D, groove diameter d, and groove radius r is subjected to a fully reversed torque T = 100 reversed moment M = 2000 lb-in. Find the factor of safety of the shaft for infinite lifetime using the modified Goodm shaft is made from steel (Sut = 85 ksi, Se = 45 ksi). Given: D = 2 in, d = 1 in, r = 0.5 in. Assume all fatigue stress concent equal to 1. M

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rope pulley is supported by two deep groove ball bearings as shown in the figure. A force of FR = 7 kN acts on the pulley in the radial direction. If Fa = 0.5kN, axial force acts. The rolling diameter of the pulley is d = 300 mm and the rope speed is v = 4 m / s. The nominal life of the bearings is required as Lh = 27000 h. Since the diameter of the shaft where the bearing is bearing is 45 mm, choose the appropriate bearing. V = N.D.n
A circular shaft of diameter D, groove diameter d, and groove radius r is subjected to a fully reversed torque T = 1000 lb-in and a fully reversed moment M = 500 lb-in. Find the factor of safety of the shaft for infinite lifetime using the modified Goodman diagram, if the shaft is made from steel (Sut = 85 ksi, Se = 45 ksi). Given: D = 2 in, d = 1 in, r = 0.5 in. Assume all fatigue stress concentration factors are equal to 1
A cylindrical steel shaft is required to transmit a bending moment of 1000 Nm and a torque of 2200 Nm with a safety factor against yielding of 3. If the steel has a yield stress of 250 MPa, find the minimum permissible diameter for the shaft. Use von Mises’ theory of yielding.
In the figure, there is a steel shaft where moment is applied from the C point. The modulus of elasticity of this shaft is 210 GPa and its shear modulus is 80 GPa. The material of the shaft is Ç1010 and the yield stress is 240 MPa.Find the shaft diameters Dab, Dbc, Dcd, Dde and the torsion angle between A and E according to the Vonmises hypothesis by taking the safety coefficient as 2
Figure shows a cantilever shaft made of steel subjected to several loadingT=5kNm, M=2.5kNm, and P=120kN. If the diameter of the shaft is 60mm, and the yield stress is 310MPa, calculate the safety of factor of the shaft using the Von Mises yield criterion.
A simply supported shaft is shown in figure below. A constant magnitude distributed unit load p=1000 Nicm is applied as the shaft rotates subject to a time-varying repeated torque that varies with maximum value of Tmar=2000 N.m. Find the diameter of shaft required to obtain a safety factor of 2 in fatigue loading if the shaft is steel of S =745 MPa and S, = 427 MPa. The dimensions (I= 20, b = 18 and a = 16) are in cm.
A turning force of 4 kN parallel to the "y" axis will be applied at the C point of the arm connected to the steel shaft AB in the figure. Accordingly, find the safe diameter value of the AB shaft using TRESCA and VON-MISES criteria.
Solve
Figure 1 shows a composite shaft ABCD acted upon horizontal forces. The moduli of elasticity and the cross-section areas of the segments of the shaft are also provided. Eal 70 GPa E = 126 GPa E = 200 GPa AAR=58 mm² ABC 77 mm2 Acp = 39 mm² Сopper 20KN 8 kN Aluminum Steel 7 kN B 20KN A 8 kN 450 mm -300 mm -- 400 mm Figure 1: Axially loaded composite shaft 2.1. Construct the diagram of internal normal forces for each cross-section of the (6) shaft (3) 2.2. Calculate the displacement of the point C with respect to the fixed-point A 2.3. If the shaft must have one uniform diameter determine the required minimum diameter of the shaft if the normal yield stress in the composite shaft must not (11) exceed 450 MPa with a factor of safety equal to 1.8.
2. Justify the simplification of this problem to only modeling one-eighth of the cross section 3. Construct two-dimensional elements grid (i.e., grid/mesh region), make the correct numbering and labeling of the nodes and elements.
at question A=110 MPa B=-60 MPa M=145N.m
A round shaft of diamater D = 65 mm with a groove cut into it where the diameter decreases to d = 50 mm. The radius of the fillet at the groove is r = %3D 2.5 mm. If the internal torsional moment at a critical cross-section in the groove is 400 N.m, calculate the maximum torsional shear stress at the groove. Round-up your answer to the nearest MPa. Max torsional shear stress MPa