A hollow steel shaft having a total length of 25cm, inner diameter of 30mm and outer diameter of 50mm is fat one end. At the free end it is loaded with an axial thrust load of 12kN, a downward transverse load of 10kNtorque of 3kN.m. Find the maximum normal stress at point A.10kN3kN.mA25cmothe12kN

Step 1: Identify the loads that will contribute to the normal stress at point A. The downward…

Answered: A hollow steel shaft having a total…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the allowable stress in shear is 60 MPa, whatis the maximum permissible torque Tmax that may beexerted with the wrench?Through what angle f (in degrees) will the shafttwist under the action of the maximum torque?(Assume G = 78 GPa and disregard any bending ofthe shaft.)
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
Torsional T is applied to the hollow axis (G=80 GPa). Ewha Womans University, the maximum shear strain is γmax = 640 × 10-6rad Igo, inside andThe outside diameters are 120mm and 150mm, respectively.a. What is the maximum axial strain?b. Maximum axial stress?c. What is the maximum torque (T) meeting the above conditions?
A shaft of diameter d is guided in rotation at A (bearing 1) and C (bearing 2) and carries two wheels supporting the indicated loads, The radius of wheel B is 200 mm, and of wheel D is 100mm. The shaft is made of steel. F2 = 6000 N. Dimensions are in mm. Calculate the diameter (mm) of the shaft considering an allowable stress of 270 MPa for a stress composed of bending and torsion.
Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner diameter. It is rigidly attached to the wall at A. Externaly applied torques are TB of 1338 lb-ft, Tc of 1117 lb-ft, and TD of 884 lb-ft. Firstly obtain the internal torque generated, then calculate and input the maximum shear stress in section BC of the shaft: (f v max) = ___________ lb/in.2. Pay attention to unit conversion and calculate your answer to 1 decimal place.
A round shaft of diamater D = 65 mm with a groove cut into it where the diameter decreases to d = 50 mm. The radius of the fillet at the groove is r = %3D 2.5 mm. If the internal torsional moment at a critical cross-section in the groove is 400 N.m, calculate the maximum torsional shear stress at the groove. Round-up your answer to the nearest MPa. Max torsional shear stress MPa

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS