A circular rod subjected to a tensile load of 13 KN having a gauge length of 30mm, extends to a length of 3mm. Given the tensile strength as 640 N\mm2, determine, a) Diameter of the rod (express in mm) b) Strain c) Modulus of elasticity (express in KPa) d) % elongation

Q: 40 - (CLO-2) The strength coefficient and strain-hardening exponent of a certain test metal are 850…

A:

Q: diameter decreases by 0.018 mm during the loading. a) Determine the Poisson's ratio of the material.…

A:

Q: Calculate the values of Poisson’s ratio of a rod under uniaxial tensile test. Initially it has 15.5…

A:

Q: In figure below, if the stress is applied at a frequency of 10 Hz,the material fails in 16minutes…

A:

Q: At a point, the normal and shear stresses acting on one plane are 90 kPa compression and 30 kPa…

A: Given data  Sigma X = -90 kpa Sigma y = -30 kpa Tau xy = 30 kpa Find principal stress and plane of…

Q: For a steel specimen, fracture occurs at an engineering stress of 253 MPa. The specimen has a 77.1 %…

A: Engineering stress = 253 Mpa Reduction in area = 77.1 %

Q: 2. Indicate the subscripts of stress components in the following cases. Use the given coordinate…

A:

Q: A circular specimen with a diameter of 1.65 and a length of 11.52 was subjected to a force equal to…

A:

Q: a) 0.2% offset yield strength b) Tensile strength

A:

Q: Integration 1) Hooke's law on a spring constant, F = kx. Where the applied force F equals the spring…

A:

Q: The stress-strain curves for two materials, A & B are plotted on the graph shown below. Please…

A: Introduction A resistive force develops inside a material to counter an external force when a…

Q: QI) A rod 150 cm long and diameter 2 cm is subjected to an axial pull of 20 kN. If the modulus of…

A: Stress is defined as the force per unit area generated within materials as a result of externally…

Q: A closed cylindrical vessel made of steel plate 10 mm thick, with a plain ends carries fluid under a…

A:

Q: The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mm…

A:

Q: Handwritten answer.  Solve f, g, h, h.

A:

Q: PROBLEM 1,25 For the assembly and loading of Prob. 1.9, determine (a) the average shearing stress in…

A:

Q: Question 1.18 The state of stress on an element has the stress components: 0,--200 MPa, and o,-150…

A: (1.18) Maximum Stress = 167.4 MPa (Option C). (1.19) Longitudinal Stress = (pr) / (2t) (Option C).

Q: Q1: A flat plate 2m long, 1m wide and 10mm thick. If a uniform tension is applied in the…

A:

Q: The stress state in which the only nonzero stress components are a single pair of shear stresses is…

A:

Q: material have a stress strain curve which can look similar to the equation y = x2 (for all x>0).…

A: Given Data⇒Stress strain curvey=x2Problem definition⇒Problem says choose between true and false.

Q: a)Determine V at x = 0.5 ft. b)Determine M at x = 4.4 ft. c)Determine M at x = 16.7 ft

A:

Q: A cylindrical aluminum alloy 10 mm in diameter and 70 mm long is pulled in tension with a force of…

A: Answer: (a) The specimen elongation is 0.21 mm. (b) The reduction in specimen diameter is 0.0099 mm.…

Q: A steel rod is subjected to a gradually applied load (F) which gave a rise to a maximum stress of…

A: Given: σmax=200MPaTotal length=250mm=ls-lcls=(250-lc)Total strain energy=1.3JE=200GPad=25mm To…

Q: The length and area of an aluminum rod are 63.99 cm and 1580 mm2 respectively. The rod is subjected…

A: Stress  Stress is defined as the ratio of load and area. It is caused by internal reactions…

Q: Q2. A circular rod subjected to a tensile load of 13 KN having a gauge length of 30mm, extends to a…

A: Given that, Length of rod, l=30 mm,Extension in the rod, δ=3 mm,Tensile load acting on the rod, F=13…

Q: A circular specimen with a diameter of 1.5 and a length of 11.74 was subjected to a force equal to…

A: Given data: d=1.5 inL=11.74 inF=150 lb Need to determine the maximum bending moment, moment of…

Q: A) 2*F(AC) i - 3*F(AC) j D B) F(AC)j 3 m y 2 m A C) F(AC) k 4 m B E FAB= F(AB)=tension force in AB…

A: Option D is correct        F(AC) i

Q: The water pressure acting on a masonry dam varies asshown. If the dam is 20 ft wide, determine the…

A: All calculations are approximate and not to scale.Please verofy ypur answers as per your need.

Q: A specimen with a circular cross sectional area has a diameter of 9 mm and initial length of 85 mm,…

A: