Answer it pls. I think it is an easy question. 2. Indicate the subscripts of stress components in the following cases. Use the givencoordinate system.a) uni-axial tension, o, = P/AMzyMy2b) Bending, o7 =С)Вending. olyMM'.TcTcd) Torsion, stress state at point A, T7e) Stress state at point C, , T77 =Both A and C are internal points near the surfaceT

Answered: Image /qna-images/answer/2eb152a0-d349-4793-8f9b-c4d20ecf3fa9.jpg

2. Indicate the subscripts of stress components in the following cases. Use the given coordinate system. a) uni-axial tension, o, = P/A Myz C)Bending, o7 = ly Mzy b) Bending, o7 M' M', M. TC Te d) Torsion, stress state at point A, T7 e) Stress state at point C, , T77 = %3D Both A and C are internal points near the surface

2. Indicate the subscripts of stress components in the following cases. Use the given coordinate system. a) uni-axial tension, o, = P/A Myz C)Bending, o7 = ly Mzy b) Bending, o7 M' M', M. TC Te d) Torsion, stress state at point A, T7 e) Stress state at point C, , T77 = %3D Both A and C are internal points near the surface

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Plane strain state shownfor the point,a) Draw the Mohr Circle.b) Principal stresses and their directionDetermine.c) Stress in the shaded C-C planeCalculate its components.d) At this point for brittle material # 2Check whether there is a break or not.
1) Figure 1 shows an element with stresses. Angle 1 Tyx Txy Tyx Figure 1 Point C)- x-direction stress 60MPA(compression), y-direction stress 40MPA(compression), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: a) From basic priciples determine the stresses on the plane of the indicated angle 1. 50° Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle. んや

3- A loaded structure with a two-dimensional stress state has the stress in the x-axis is 13.5 Mpa, in the y-axis is - 3.2 Mpa, and the shear stress in the x-y is - 4.4 Mpa. a) Write the stress transformation equations b) Calculate o and t for the inclination angle 0 between the n values 0 to 180°, in 15° increments. c) Draw the profile graph of normal stress and shear stress with e in the x-axis d) Obtain from the graph, the principal stresses o,, o,, and 2' maximum and minimum shear stresses Tmax and tmin e) Obtain from the graph the corresponding inclination angle Op1, Op2, Os1, and es2 for each of principal stresses and shear stresses, respectively
Stress vs. Strain 517 465 414 362 310 155 103 51.7 5.00 10.0 15.0 20.0 30.0 35.0 40.0 45.0 50.0 Strain (%) Stress (MPa)
When an object is placed underwater, the pressure on the object is subjected to uniform stress on all sides. a) define volume strain, the bulk modulus, compressibility, and the relationship between the bulk modulus and compressibility. b) A 100 litre volume of liquid is subjected to a 2000 psi increase. If the compressibility of the liquid is 5 x 10-5 per atm, find the bulk strain and absolute decrease in the volume of the liquid c) explain the concepts of shear stress and shear strain? could these concepts be applied to the fluid problem above?
P1. The below picture shows a three-point bending test of the bone specimen, Given the below loading condition a) Draw shear force diagram b) Determine the maximum shear force c) Determine the maximum transverse shear stress in the bone 1000N 25cm c=2cm 5cm 50cm 5cm 500N 500N Note: Use the following centroid formula for half circle when you calculate Q Centroid (X,y) (Answer: Tmax =0.53MPA) 4r 3
7 - A) 2*F(AC) i - 3*F(AC) jB) F(AC) kC) F(AC) iD) F(AC) j
%VY .. B2TE.pdf Q)The state of plane stress at a point is represented by the stress element below: A. Draw the Mohr's Circle. B. Determine the principle stresses and draw the corresponding stress elements. C. Determine the maximum shear stress and draw the corresponding stress element. D. Find the stresses on an element inclined at 30° anti clockwise and draw the corresponding stress element. E. Provide a table illustrating the stress values as well as the inclination angles and compare the obtained values from Mohr's Circle with those obtained from equations 60 MPa 50 MPa 30 MPa II >
Choose the correct answer from the following
I need help with this problem
- Lo° do A solid cylindrical bar is subjected to tensile test. The initial diameter of the bar is 60 mm. The change in diameter (Ad) after the test is 0,01438 mn The applied load is 130 kN. The inital length of the bar is 240 mm. The change in length (Al) after the test is 0,1987 mm. Evaluate the axial strain. O A) 0,1987 O B) 0,01438 C) 0,000239 O D) 0,000275 E) 0.000828
Handwritten answer. Solve f, g, h, h.