Answered: A circular coil X with 10 turns is… | bartleby

Related questions

Question

A circular coil X with 10 turns is placed with its plane perpendicular to the uniform magnetic field. Which of the following will induce continuous decreasing emf in the coil?

A. Decrease the area of coil X with increasing speed

B. Move coil X upwards with increasing speed

C. Increase the area of coil X with decreasing speed

D. Rotate coil X with constant speed

Expert Solution

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

Question 8 A bar magnet enters a long solenoid which has an ammeter attached in series to both ends. Explain why a reading on the ammeter is briefly shown and then records zero current. A The magnetic flux linkage in the coil increases and then decreases. The magnetic flux linkage in the coil decreases and then increases. The magnetic flux linkage in the coil increases and is then constant. D The magnetic flux linkage in the coil is always constant. B C
2. A 22 cm by 35 cm rectangular coil has a single turn and carries a current of 1.4 A. Initially the plane of the coil is perpendicular to a uniform 1.6 T magnetic field, as shown in the picture O below. The resistance of the coil is negligible. a. Please determine the direction and the magnitude of the magnetic force on the right side of the coil. b. If the coil rotates a 30° angle as shown in the picture 2, please determine the direction and the magnitude of the magnetic torque on the left side of the coil. Axis B x x x xi x 22.0 cm 35.0 cm 30° x B
Two identical coils (coil A and coil B) of wire are mounted parallel so that their axes coincide. Neither carries any current. As you begin to run current through coil A, the induced current in the coil B will be a. zero b. In the same direction as coil A c. In the opposite direction as coil A d. not enough information
The sketches below show a circular coil and a permanent magnet; the arrows indicate both the magnitude and the direction of the velocities of the magnet and coil. Select all the true statements. If no statements are true, select "None of the above." A. The induced voltage in A is zero.B. The induced voltage in F is non-zero.C. The induced voltage in D is zero.D. The induced voltage in C is non-zero.E. The induced voltage in E is zero.F. The induced voltage in B is zero.G. The induced voltage in G is non-zero.H. None of the above. I keep thinking that the correct statements are B. C. D. but I keep getting the question wrong.
A current of 4.0 A is maintained in a circular loop with radius 20.4 cm that consists of 50 turns of wire. An external magnetic field of 2.0 T is directed so that the angle between the field and the plane of the loop is 20°. Determine the magnitude of the torque exerted on the loop by the magnetic forces acting upon it. a. 17.9 N.m b. 0.9 N.m c. 49.1 N.m d. 62.4 N.m e. 83.2 N.m
When a magnet is passed through a conducting wire coil, the changing magnetic flux will induce A. an electromagnetic force in the coil. B. a neutral charge on the Faraday Ice Coil. C. a positive charge on the Faraday Ice Pail. D. a negative charge on the Faraday Ice Coil.
36. How many turns must be wound on a flat, circular coil of radius 20 cm in order to produce a magnetic field of magnitude 4.0 x 10-5T at the center of the coil when the current through it is 0.85 A? 38. A circular loop of radius R carries a current I. At what distance along the axis of the loop is the magnetic field one-half its value at the center of the loop?
1. A student uses a coil of radius 14 cm with 90 windings.a) Calculate the expected slope for a plot of magnetic field vs current in this coil.b) She performs the lab and measures a slope of 4.2 x 10^-4 T/A. Based on this slope, what valuedoes she calculate for μo ?c) Calculate the percent error between her measured value of μo and the theoretical value.2. She then uses a permanent magnet of strength B = 0.5 mT to induce a voltage in the (same) coil.Calculate the expected voltage if she pulls the magnet from the coil in 0.02 seconds.
QUESTION 23 In generating electricity, a magnet, surrounded by wires connected to the electrical grid, will be made to spin, using wind, a steam turbine, or moving water. Which answer best explains what is happening in the wires during this process. a. The magnet does not need to move, and still has the capability to make electrons move in the wires that surround it. b. An induced voltage and current flow is set up in the wires surrounding a magnet due to changes in magnetic temperature. c. A magnetic field surrounds the rotating magnet, pushes on the electrons in the wires, thus giving those electrons energy per charge (voltage). d. Light from the magnet is able to push electrons out of the material that makes up the wires. In so doing, the wires are made to have a flowing electrical current.
If number of turns (N), area (A) and magnetic field (B) have same value for a square and circular loop, but current of square loop is half the current in the circular loop then maximum torque produced in the circular loop will be 1/2 a. 4 times the torque in square loop O b. Double the torque in square loop c. Half of torque in square loop O d. Equal the torque in square loop
20. The image shows a non-constant B-field driving a counter clockwise current in a loop of wire with radius R. For B = et², what is the E-field on the wire at radius R? A. B. C. D. E. tet² R tet² R² tet² R tet2 R² None of the above X X X X X X R X X
When you push the South end of a magnet into a solenoid, it creates a negative voltage. If you push the North end of a magnet into the solenoid, it will create A. no voltage B. a negative voltage C. a positive voltage D. a capacitor

SEE MORE QUESTIONS