A chemist needs to determine the concentration of a sulfuric acid solution by titration with a standard sodium hydroxide solution. He has a 0.1375 M standard sodium hydroxide solution. He takes a 25.00 mL sample of the original acid solution and dilutes it to 250.0 mL. Then, he takes a 10.00 mL sample of the dilute acid solution and titrates it with the standard solution. The endpoint was reached after the addition of 17.56 mL of the standard solution. What is the concentration of the original sulfuric acid solution? concentration: M > TOOLS x10

A chemist needs to determine the concentration of a sulfuric acid solution by titration with a standard sodium hydroxide solution. He has a 0.1375 M standard sodium hydroxide solution. He takes a 25.00 mL sample of the original acid solution and dilutes it to 250.0 mL. Then, he takes a 10.00 mL sample of the dilute acid solution and titrates it with the standard solution. The endpoint was reached after the addition of 17.56 mL of the standard solution. What is the concentration of the original sulfuric acid solution? concentration: M > TOOLS x10

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A strong acid-strong base titration was performed as follows: 10.00 mL of 0.10M HCl were collected in an Erlenmeyer flask, and then diluted to 100 mL with distilled water. After that, two drops of indicator were added. Then, the buret was filled with 0.100 M NaOH. The titration was started by slowly adding NaOH to HCl. (Note: The volume of two drops indicator is ignored as it is so tiny compared with 100 mL.) What is the pH of the solution in the Erlenmeyer flask after adding 10.20 ml of 0.100M NaOH? Select one:a. 9.80b. 10.26c. 9.90d. 11.08
A 0.500 M solution of KCl needs to be prepared through dilution. A 2.00 M stock solution will be added to a 0.250 L volumetric flask and then water will be added to the 0.250 L mark. Determine the volume (in mL) of the 2.00 M stock solution of KCl needed to produce this solution.
A 0.124 M NaOH(aq) solution was used to titrate 20.00 mL of an acetic acid (CH3COOH) solution that has an unknown concentration. The equivalence point is reached after adding 15.34 mL of NaOH(aq). a) Write out the complete balanced equation for the reaction that occurs in this titration. b) How man moles of NaOH were added to the acetic acid solution? c) How many moles of acetic acid were in the original 20.00 mL solution? d) What was the concentration of acetic acid in the orignial 20.00 mL solution?
A chemist needs to determine the concentration of a sulfuric acid solution by titration with a standard sodium hydroxide solution. He has a 0.1886 M0.1886 M standard sodium hydroxide solution. He takes a 25.00 mL25.00 mL sample of the original acid solution and dilutes it to 250.0 mL.250.0 mL. Then, he takes a 10.00 mL10.00 mL sample of the dilute acid solution and titrates it with the standard solution. The endpoint was reached after the addition of 12.42 mL12.42 mL of the standard solution. What is the concentration of the original sulfuric acid solution?
4. A student did not read the directions to the experiment properly and mixed up where to put the NaOH and the HCl solutions. He put the HCl in the buret and the NaOH in the flask. He then added a drop of the phenolphthalein to the solution in the flask. Does the student need to empty out all of the solutions and start over again or can he go ahead and run the titration? Explain qalb ribidw qid edini olddud ris ogrel s znisimos tund entd nousu 5. How many liters of 3.4 M HI will be required to reach the equivalence point with 2.1 L of 2.0 M KOH? 9no vino to beateni nolusius to alsid sigulum ob of insttoqmi ti al VW S
An analytical chemist weighs out 0.091 g of an unknown triprotic acid into a 250 mL volumetric flask and dilutes to the mark with distilled water. He then titrates this solution with 0.1200M NaOH solution. When the titration reaches the equivalence point, the chemist finds he has added 23.2 mL of NaOH solution. Calculate the molar mass of the unknown acid. Round your answer to 2 significant digits. mol ?
A student is asked to standardize a solution of calcium hydroxide. He weighs out 1.09 g potassium hydrogen phthalate (KHC8H404, treat this as a monoprotic acid). It requires 37.2 mL of calcium hydroxide to reach the endpoint. A. What is the molarity of the calcium hydroxide solution? This calcium hydroxide solution is then used to titrate an unknown solution of hydrobromic acid. B. If 18.1 mL of the calcium hydroxide solution is required to neutralize 24.6 mL of hydrobromic acid, what is the molarity of the hydrobromic acid solution? M M
A 0.0715 M solution of NaNO₃ needs to be prepared through dilution. A 0.500 M stock solution will be added to a 1.000 L volumetric flask and then water will be added to the 1.000 L mark. Determine the volume (in mL) of this 0.500 M stock solution of NaNO₃ needed to produce this solution.
A 0.249 M sodium hydroxide solution required 25.00 mL to titrate 10.0 mL of an unknown concentration of sulfuric acid. Calculate the molarity of the sulfuric acid solution.
A chemistry student weighs out 0.0570 g of citric acid (H,C,H,0,), a triprotic acid, into a 250. mL volumetric flask and dilutes to the mark with distilled water. He plans to titrate the acid with 0.1900 M NaOH solution. Calculate the volume of NaOH solution the student will need to add to reach the final equivalence point. Be sure your answer has the correct number of significant digits. O mL x10
A researcher has a sample of potassium chloride that is contaminated with magnesium chloride. They weigh 5.00 g of the sample, dissolve it in 1.00 L of water, and determine the chloride ion concentration to be 0.0708 M. What mass (in g) of the 5.00 g sample was magnesium chloride?
A 25.00 mL sample of sodium hydroxide was titrated (neutralized) with 36.4 mL of 0.125 M sulfuric acid. What is the concentration of the sodium hydroxide solution? Group of answer choices 0.364 M 0.728 M 1.46 M 0.091 M 0.182 M