A certain room located at 40'N. Lat has a south-cast wall consisted of 100mm face brick, 200mm concrete block and gypsum plaster (U=2 W/m²."C). This wall contains a regular glass window with light roller shade. Find the heat gain per unit area of the wall and window for Aug at 4PM, if the inside and average outside temperatures are 26°C and 36°C respectively.

A certain room located at 40'N. Lat has a south-cast wall consisted of 100mm face brick, 200mm concrete block and gypsum plaster (U=2 W/m²."C). This wall contains a regular glass window with light roller shade. Find the heat gain per unit area of the wall and window for Aug at 4PM, if the inside and average outside temperatures are 26°C and 36°C respectively.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Define Heat conduction from warm air to a cold canned drink through the wall of the aluminum can.
REFERENCE: FROM BOOK - ENGINEERING THERMOFLUIDS, M. MASSOUD
I need right solution with clear calculations. A workplace is occupied by 100 people who are averaging 250 Watts/person. The space is measured as 30 meters x 20 meters x 15 meters (L x W x H). What is the internal heat gain of this space given off by a full staff? If you need to provide the workplace 10 air changes per hour, what type of infiltration inflow rate need to be (cubic meters/hour)?
A steam pipe 20cm in diameter is protected with a covering 6cm thick for which thecoefficient of thermal conductivity is k=0.003cal/cm deg. Sec in steady state .Find theheat lost per hour through a meter length of the pipe , if the surface of pipe is at 2000cand outer surface of the covering is at 300c
105 W/m3 heat is uniformly generating within a 4 cm thick slab. The slab is exposed to ho = 10 W/m2K and To = 20 °C ambient conditions from its both sides. What is the surface temperature of the slab? A. 420 °C B. 200 °C C. 220 °C D. 100 °C
Select the correct statement for a radial conductivity exp Select one: a. The mid outer surface represent the heating area while the side surface represent the cooling area b. None of them is true c. The inner section represent the heating area and the outer section represent the cooling area d. The outer section represent the heating area and the inner section represent the cooling area
You are designing a PCB laid horizontally on the ground. The PCB surface temperature can’t exceed 85℃ and has a size of 96mm x 90mm. Tinfinity = 45oC. "p" is the perimeter of the plate a) Calculate the Rayleigh number. b) If the PCB is laid hot-side UP, what is the Nusselt number and heat transfer coefficient? c) If the PCB is laid hot-side DOWN, what is the Nusselt number and heat transfer coefficient? d) Given your results from b and c, which one has better heat transfer? In that case, what is the maximum power dissipation the board can put out? Properties of Air:k = 0.025 W/mkPr = 0.72v = 1.847 x 10−5u = 16.84 x10−6p = 1.2 kg/m3B =1/ Tf (idwal gass)
solve Q3 please dont late
Please good handwriting and clear ideas explaining the process! a) Calculate the equilibrium temperature inside the submarine
A linear thermal actuator is being used, inside it contains wax with a specific volume of 15%, that is, the expansion of the wax is 15%. however, the wax chamber is to big for the wax to cover, how small can the chamber be for the wax to expand at this rate? What dimensions can I get? and how far could I push a piston rod with that expansion rate the required stroke length is 0.300 in Piston rod dimensions: 3.90 height and 0.30 diameter the wax chamber in a hollow cylinder since the wax is inside expanding. What dimensions could be the most suitable?