2. One side of a copper block 4 cm thick is maintained at 175-C. The other side is covered with a layer of fiberglass 1.5 cm thick. The outside of the fiberglass is maintained at 80°C, and the total heat flow through the composite slab is 300 W. What is the area of the slab?

2. One side of a copper block 4 cm thick is maintained at 175-C. The other side is covered with a layer of fiberglass 1.5 cm thick. The outside of the fiberglass is maintained at 80°C, and the total heat flow through the composite slab is 300 W. What is the area of the slab?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An aluminum tube is 200 cm long and has a outside diameter of 2 cm and wall thickness of 5 mm. One end is kept at a constant temperature of 300°C and the other is kept at a temperature or 10 °C. Assume the tube sides are adiabatic. Calculate the heat transfer through the tube. Use finite difference analysis to calculate the temperature very 10 cms.
The thermal conductivity of 304 stainless steel is 14.4 W/m K. PROBLEM 2: A copper slab (k = 387 W/m K) is 3 mm thick. It is protected from corrosion on each side by a 2-mm-thick layer of stainless steel (k = 17 W/m K). The temperature is 400°C on one side of this composite wall and 100°C on the other. Find the temperature distribution in the copper slab and the heat conducted through the wall.
A cold-storage room is constructed of an inner layer of 11 mm of pine with thermal conductivity of 0.15 W/m K, and an outer layer of 75 mm of concrete with thermal conductivity of 0.75 W/m K. The wall surface temperature is 253 K inside the cold room and 299 K at the outside surface of the concrete. Calculate the heat loss in W per 1 m2. Please keep one decimal and take positive value for the final answer.
Consider a multi-layered walls of a storage building (no windows) that is made of three layers as shown in the figure. The inside layer is a gypsum material that is 1.0 cm thick and has a thermal conductivity of 0.5 W/m.K. We then have a dense brick layer that is 15.0 cm thick and has a thermal conductivity of k = 5 W/m.K The outside wall is made of a wood panel that is 2.0 cm thick and has a thermal conductivity of k = 1.0 W/m.K In a cold day, the outside can be at -10oC and the convective heat transfer coefficient can be hout = 25 W/m2.K due to wind. Inside air of the building is kept at 10oC and the convective heat transfer coefficient over the inside surfaces is rather low with hin = 5 W/m2.K a) Show the thermal resistance diagram with all the temperature nodes. b) What is the rate of heat loss in kW per m2 under these conditions? c) What would be the temperature of the inside surface of the wall? d) What is the temperature at the interface between the brick wall and the plywood?…
A composite structural wall having a thermal conductivity of 0.3 W/mK and a thickness of 100 mm is being replaced by a concrete wall having thermal conductivity 0.9 W/mK. If the heat rate is to be 80% of the heat rate through the composite wall, the wall thickness (in mm) required for concrete wall is. Assume both walls are subjected to the same surface temperature difference.
Problem 2- Consider a square bar with a side length of 20 cm as shown in the figure. The lower side of the bar is kept at 70°C, and the left side of the bar is insulated. Thermal çonductivity of the bar is 1.5 W/m°C. The upper and right surfaces of the bar are in contact with the air at 20°C and the heat transfer coefficient on these surfaces are 1oW/m*C. The bar is in steady state condition. Find the 2. temperatures at points 1 and 2 of the bar. 20cm とこがん
There is a 1.20-cm-thick stagnant air pocket. A) What thickness of cork would have the same R-factor as the stagnant air pocket? The thermal conductivity of air is 0.0230 W/m·K and of cork is 0.0460 W/m·K.in cm B) What thickness of tin would be required for the same R-factor as a 1.20-cm-thick stagnant air pocket? The thermal conductivity of air is 0.0230 W/m·K and of tin is 66.8 W/m·K . in m i asked how to do this but got the wrong soloution
It is designed in such a way that the internal temperature of a commercial heat treatment furnace can reach up to 165 oC. All surfaces of the furnace consist of firebrick (10 cm), insulation material and sheet metal (3mm) from the inside out. Given that the outdoor temperature is 22 oC, the outer sheet will be allowed to go up to 35 oC, which is a temperature that will not disturb in contact with hands. In this case, determine the insulation material thickness to be used. The thermal conductivity coefficient of the insulation material is insulation 0.066 W / m oC, 60 W / m oC for sheet metal and 115 W / m oC for firebrick. Indoor heat transfer coefficient will be accepted as 25 W / m2 oC and 12 W / m2 oC for outdoor environment.
Homework problem for unsteady-state heat transfer Consider a product to be sterilized if its coldest location during heating reaches 115°C. Consider sterilization of potatoes where potatoes (4 cm diameter) is heated in steam at 121°C. Assume symmetrical heating of potatoes and the heat transfer coefficient between the steam and the potatoes is 20 W/m² K. The thermal diffusivity for potatoes is 1.5 × 107m²/s and the thermal conductivity is 0.4 W/m K. The potatoes are initially at 30°C. 1) Calculate the heating time needed for sterilization. 2) Calculate the temperature at the center of the potato after heating 1000 s and 2000 s. Plot how the temperature at the center changes with time t. 3) Calculate the temperature at the surface of the potato at 2000 s. Qualitatively plot how the temperature changes across the apple at t = 2000 s.
What is(roughness)? what is its effect on heat transfer? Write one or two pages providing schemes or illustration for more demonstration.