105 W/m3 heat is uniformly generating within a 4 cm thick slab. The slab is exposed to ho = 10 W/m2K and To = 20 °C ambient conditions from its both sides. What is the surface temperature of the slab? A. 420 °C B. 200 °C C. 220 °C D. 100 °C

105 W/m3 heat is uniformly generating within a 4 cm thick slab. The slab is exposed to ho = 10 W/m2K and To = 20 °C ambient conditions from its both sides. What is the surface temperature of the slab? A. 420 °C B. 200 °C C. 220 °C D. 100 °C

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.47P

See similar textbooks

Similar questions

Using Table 1.4 as a guide, prepare a similar table showing the orders of magnitude of the thermal resistances of a unit area for convection between a surface and various fluids.
1.77 Explain each in your own words. (a) What is the mode of heat transfer through a large steel plate that has its surfaces at specified temperatures? (b) What are the modes when the temperature on one surface of the steel plate is not specified, but the surface is exposed to a fluid at a specified temperature?
Discuss the modes of heat transfer that determine the equilibrium temperature of the space shuttle Endeavour when it is in orbit. What happens when it reenters the earths atmosphere?
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
A high-speed computer is located in a temperature-controlled room at 26C. When the machine is operating, its internal heat generation rate is estimated to be 800 W. The external surface temperature of the computer is to be maintained below 85C. The heat transfer coefficient for the surface of the computer is estimated to be 10W/m2K. What surface area would be necessary to assure safe operation of this machine? Comment on ways to reduce this area.
1.3 A furnace wall is to be constructed of brick having standard dimensions of Two kinds of material are available. One has a maximum usable temperature of 1040°C and a thermal conductivity of 1.7 W/(m K), and the other has a maximum temperature limit of 870°C and a thermal conductivity of 0.85 W/(m K). The bricks have the same cost and are laid in any manner, but we wish to design the most economical wall for a furnace with a temperature of 1040°C on the hot side and 200°C on the cold side. If the maximum amount of heat transfer permissible is 950 , determine the most economical arrangement using the available bricks.
As a designer working for a major electric appliance manufacturer, you are required to estimate the amount of fiberglass insulation packing (k = 0.035 W/m K) that is needed for a kitchen oven shown in the figure below. The fiberglass layer is to be sandwiched between a 2-mm-thick aluminum cladding plate on the outside and a 5-mm-thick stainless steel plate on the inside that forms the core of the oven. The insulation thickness is such that the outside cladding temperature does not exceed 40C when the temperature at the inside surface of the oven is 300C. Also, the air temperature in the kitchen varies from 15Cto33C, and the average heat transfer coefficient between the outer surface of the oven and air is estimated to be 12.0W/m2K. Determine the thickness of the fiberglass insulation that is required for these conditions. What would be the outer surface temperature when the inside surface of the oven is at 475C?
1.76 Explain a fundamental characteristic that differentiates conduction from convection and radiation.
The thermal conductivity of fibreglass insulation at 67F is 0.02 Btu/h ft F. What is its value in SI units?
Wearing layers of clothing in cold weather is often recommended because dead-air spaces between the layers keep the body warm. The explanation for this is that the heat loss from the body is less. Compare the rate of heat loss for a single 2-cm-thick layer of wool [k=0.04W/(mK)] with three 0.67-cm layers separated by 1.5 mm air gaps. The thermal conductivity of air is 0.024 W(mK).
2.30 An electrical heater capable of generating 10,000 W is to be designed. The heating element is to be a stainless steel wire having an electrical resistivity of ohm-centimeter. The operating temperature of the stainless steel is to be no more than 1260°C. The heat transfer coefficient at the outer surface is expected to be no less than in a medium whose maximum temperature is 93°C. A transformer capable of delivering current at 9 and 12 V is available. Determine a suitable size for the wire, the current required, and discuss what effect a reduction in the heat transfer coefficient would have. (Hint: Demonstrate first that the temperature drop between the center and the surface of the wire is independent of the wire diameter, and determine its value.)
GChoose the right answer 1. The temperature profile for steady hest conduction through a plane wall of constant thermal conductivity is a. logarithmic b. parabolic 2. A brick wall (k-0.75 W/mK ) transmits $02 of heat loss through another wall (k-0.25 W/mK, x-100 mm). If the temperature difference across both walls is the same, the thickness of the brick wall would be a.150 mm c. linear 6T b. 240 mm c. 300 mm d. 375 mm 3. The maximum temperature at the center of the solid sphere of radius R having heat generation q (W/m') is given by g'R +9R b. T, + 4k T+9R 6k d. T+9R 8k a. 2k C. 4. The internal thermal resistance of a solid can be ignored if the Biot number is less than a. 1 b. 0.5 c. 0.1 d. Fourier number 5. The ratio of heat transfer of a fin to the heat transfer without fin is referred to as a. fin resistance b. fin efficieney efin effectiveness d. fin conductance.