A ceramic matrix composite contains internal flaws as largeas0.001 cm in length. The plane strain fracture toughness of the composite is 45 MPaVm and the tensile strength is 550 MPa. Will the stress cause the composite to fail before the tensile strength is reached? Assume that f- 1.

A ceramic matrix composite contains internal flaws as largeas0.001 cm in length. The plane strain fracture toughness of the composite is 45 MPaVm and the tensile strength is 550 MPa. Will the stress cause the composite to fail before the tensile strength is reached? Assume that f- 1.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: AS 3600-2009 tensile steel ratio P=0.0376, yield strength of reinforcing steel fy 500 MPa, fe 40…

A: Given:- The tensile steel ratio = 0.0376 The yield strength of the steel = fy = 500 MPa The…

Q: The first parts of the stress-strain relationships of the components of a randomly oriented…

A: Given:- The first parts of the stress-strain relationships are given for a randomly oriented…

Q: When a fiber-reinforced polymer matrix composite plate is fractured in bending, what evidence may…

A: Fibre-Reinforced Polymer (FRP) is a composite material made of a polymer matrix reinforced with…

Q: A composite beam is made of two brass [E = 110 GPa] bars bonded to two aluminum [E = 71 GPa] bars,…

A: Bending moment=260Nm a=10mm b=85mm c=20mm d=55mm

Q: Given the beam cross-section in 1. MCR and OCR (Negative be: 2. Steel stress before and aft 3.…

Q: below. The specimen dimensions are length=254 mm, width=12. 1.4 mm. Determine the tensile modulus…

A: solution stress = LoadArea area = width×thickness = 12.7×1.4 = 17.78 mm2 to…

Q: Three metal strips, each 40 mm height, are bonded together to form the composite beam shown. The…

A: here m ,modular ratio is m = Esteel/ E another now , width of brass is 40/ mnow widht barss is 20mm…

Q: It is necessary to fabricate an aligned and discontinuous carbon fibre-epoxy matrix composite having…

Q: 3-21. The stress-strain diagram for a polyester resin is given in the figure. If the rigid beam is…

A: P = 80 kN or 80,000 N d = 40 mmD = 80 mm

Q: A square specimen of Magnesium Oxide is loaded in a 3-point bending test. If w = h = 6.2 mm is the…

A: Given Data: Load applied= 494 N h=w=6.2 mm Flexural strength= 117.1 MPa

Q: A tensile test specimen of stainless steel alloy having a diameter of 0.550 in. and a gage length of…

Q: for a fiber reinforced composite material, assume Fibre's volume fraction is 0.3. what is the…

Q: Name three functions of the matrix phase in fiber-reinforced composites. State the reason for the…

A: The material which has high strength / weight and also modulus/weight and has three components of…

Q: Problem 4.4 The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to…

Q: V- It is necessary to design a continuous and aligned glass fiber-reinforced polyester having a…

Question

A ceramic matrix composite contains
internal flaws as largeas0.001 cm in length.
The plane strain fracture toughness of the
composite is 45 MPaVm and the tensile
strength is 550 MPa. Will the stress cause
the composite to fail before the tensile
strength is reached? Assume that f- 1.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution:-

Step 2 Solution:-

Step 3 Solution:-

Step 4 Answer:-

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

AS3600-2009
The first parts of the stress-strain relationships of the components of a randomly oriented composite are shown in Figure P11.25. Estimate the volume percentage of fibers in the composite assuming a fiber efficiency parameter (K) of 0.2. Stress (MPa) 1400 1200 1000 800 600 400 200 I T FIGURE P11.25 0.002 Fibers Strain (m/m) 0.004 Composite Matrix 0.006
pls show me a solution.
For the tensile steel ratio P 0.0376, yield strength of reinforcing steel fy 500 MPa, fe 40 MPa, find fs, which is the maximum tensile stress permitted in the reinforcement immediately after the formation of a crack. AS 3600- 2009 Explain steps
The composite bar, firmly attached to unyielding supports, is initially stress-free. What maximum axial load P can be applied if the allowable stresses are 10 ksi for aluminum and 18 ksi for steel?
A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Taking h= 9 mm and using the data given below, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis. Brass Aluminum 30 mm Modulus of elasticity Allowable stress h 30 mm h Aluminum 70 GPa 100 MPa The largest permissible bending moment is Brass 105 GPa 160 MPa 1.17 kN-m.
A steel specimen is tested in tension. The specimen is 1" wide by 0.5" thick in the test region. By monitoring the stresses from the testing machine, it was found that the specimen yielded at a stress of 72 ksi and fractured at 96 ksi. (a). Determine the tensile loads at yield and at fracture
Which of the following is not a factor contributing to fatigue in a steel structure? oints) a) Repetitive tensile stress cycles b) Dead load stresses c) Microstructural damage d) Tri-axial state of stress
A composite sample of carbon reinforced epoxy has dimensions of in 20 in x 20 in x 0.135 in and mass of 3 lb. The carbon fibres have a modulus of elasticity of 80(106) lb/in2 and a density of 0.15 lb/in3. The epoxy matrix has modulus of elasticity of 0.90(106) lb/in2 and a density of 0.05 lb/in3. Assume there are no voids in the sample, calculate the volume fraction of: (i) The carbon fibres (ii) The epoxy matrix in the sample.
A composite primary steel beam with a span of 8m supports a secondary beam at midspan, which applies an characteristic (unfactored) load of 239kN to the primary beam. What elastic modulus (in cm³) does the beam require to be able to carry the load if the allowable stress due to the characteristic loads is 210N/mm2? It may be assumed that the elastic modulus required for the composite beam is 63% of that required for the equivalent non-composite beam.
The composite shaft shown consists of a solid brass segment (1) and a solid aluminum segment (2) that are connected at flange B and securely attached to rigid walls at A and C. Brass segment (1) has a diameter of 18 mm, a length of L₁ 235 mm, and a shear modulus of 39 GPa. Aluminum segment (2) has a diameter of 24 mm, a length of L₂ = 165 mm, and a shear modulus of 28 GPa. If a concentrated torque of 270 N-m is applied to flange B, determine (a) the maximum shear stress magnitudes in segments (1) and (2). (b) the rotation angle of flange B relative to support A. N 235 mm (1) B 165 mm Partial Ans: Max shear stress in Member 1 is 55.7 MPa 270 N-m (2)
A discontinuous fibre reinforced composite consists of 20mm long carbon fibres in a polymer matrix. The volume fraction of the composite is 0.5, interfacial shear strength 5MPa and the critical fibre length 2.5mm. The fibre modulus is 250GPA and strain to failure 1.5%. The matrix modulus is 3.5GPa and failure strain 10%. If the ultimate fibre strength = 3500MPa, calculate the average failure stress in the composite.