For the tensile steel ratio P 0.0376, yield strength of reinforcing steel fy 500 MPa, fe 40 MPa, find fs, which is the maximum tensile stress permitted in the reinforcement immediately after the formation of a crack. AS 3600- 2009 Explain steps

For the tensile steel ratio P 0.0376, yield strength of reinforcing steel fy 500 MPa, fe 40 MPa, find fs, which is the maximum tensile stress permitted in the reinforcement immediately after the formation of a crack. AS 3600- 2009 Explain steps

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: AS 3600-2009 tensile steel ratio P=0.0376, yield strength of reinforcing steel fy 500 MPa, fe 40…

A: Given:- The tensile steel ratio = 0.0376 The yield strength of the steel = fy = 500 MPa The…

Q: Tie bars of 12 mm diameter are to be provided in a concrete pavement slab. The working tensile…

Q: In a fillet weld, the direct shear stress and bending tensile stress are 50 MPa and 150 MPa…

Q: 1 in. 2.5 in.

Q: A Charpy V Notch (CVN) test was performed on a steel specimen and pro- duced the readings shown in…

A: Tabulate the values that are used to plot the graph. Temperature, C Toughness, Joule (N.m) 40 7…

Q: For a specimen of a steel alloy with a plane strain fracture toughness of 80 MPa√m, fracture results…

A: Given KIC=80MPamσ=510MPaa=6mm Consider the formula KIC=Yσπa80=Y×5103.14×6Y=0.036

Q: tie bars (in mm, round off to the nearest Tie bars of 12 mm diameter are to be provided in a…

Q: petween a tie bar and concrete is 2 MPa, and the joint gap between the slabs is 10 mm. Ignoring the…

A: Using formula

Q: In Brinell hardness test, which is harder steel or aluminum? Should changing the load affect the…

A: Solution: The Brinell Hardness Test was proposed by J. A Brinell in 1990 is considered one of the…

Q: Q 3. (a) Draw a typical stress-strain diagram for a tensile test on mile steel. Discuss the…

Q: FL b FL What is the change in length (L) of the titanium bar (E = 16.5E6 psi) given: L = 36 in., b =…

A: F = 4 Kips

Q: A tension test for a steel alloy results in the stress-strain diagram shown in Figure. Calculate the…

A: Consider the graph,

Q: Strain energy of mild steel specimen

A: WE HAVE TO FIND OUT STRAIN ENERGY STORED IN MILD STEEL SPECIMEN

Q: 2. The Goodman diagram relates oa and om for fatigue failure after a specific number of cycles N₁,…

A: Given, Fatigue strength under zero mean stress , σa(0) = 0.45 σTS Tensile strength, σTS = 375…

Q: Tie bars of 12 mm diameter are to be provided in a concrete pavement slab. The working tensile…

Q: A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If…

A: we have to find the increase in volume

Q: In a fillet weld, the direct shear stress and bending tensile stress are 50 MPa and 150 MPa…

A: Given data- direct shear stress q=50 MPabending tensile stress σb=150 MPaTo Find-The value of…

Q: the terms: limit of proportionality, elastic stage, yield strength, ultimate

A: given data,question related to the strength of material terms are given limit of…

Q: Elastic stress of a mild steel specimen in the tensile test is found to be 250 N/mm² and neck…

Q: Prob- In a tensile test carried out in the laboratory on a steel specimen for 5 minutes. The strain…

A: given- strain=0.30time=5 mintues

Q: The state of two-dimensional stresses acting on a concrete lamina consists of a direct tensile…

A: given- Direct tensile stress-σx=1.5 N/mm2σy=0Shear stress-τxy=1.2 MPa

Q: Tensille strengin 450 MPa (65,000 psi) Strain = 0 Stress = 0 MPA 500 Stress = 0 psi 70 Strain = 0…

Q: For the tensile steel ratio P 0.0376, yield strength of reinforcing steel fy 500 MPa, fe 40 MPa,…

A: Given Steel ratio ρ=0.0376and stress in concrete fc'=40 MPa and stress in concrete fsy'=500Mpa…

Q: A hollow steel cylinder 3.5m which has an inside diameter and outside diameter of 55mm and 35mm. If…

A: Given Data length of the cylinder = 3.5m = 3500 mm Outer diameter ,Do=55 mm Inner diameter , Di=35…

Q: A steel specimen is tested in tension. The specimen is 1" wide by 0.5" thick in the test region. By…

A: Given: The width of the specimen is 1 in. The thickness of the specimen is 0.5 in. The yield stress…

Q: ngth of 250 MPa. How much shear stress can the plate resist before it yields according to the…

A: Given data yield strength, fy =250MPa Draw the diagram In case of Pure shear Major principal…

Q: particular geometry, the value of Y is 1.3. Assuming a design stress of 0.4 times the yield…

A: According to given data shape of a flat plate 24.3 mm strain fracture toughness values are 533 MPa…

Q: The aluminum shell is fully bonded to the brass core, and the assembly is unstressed at a…

A: Given Data:Temperature of 78°FChange in Temperature = 210°FBrass…

Q: 2. The Goodman diagram relates oa and om for fatigue failure after a specific num of cycles Nf,…

A: Fatigue strength under zero mean stress , Tensile strength, Number of cycles to failure, N = 107…

Q: A mild steel bar of 2cm is subject to tensile test. The bar yields under a load of 80kN. It reaches…

A: Given data, Diameter of steel bar = 2 cm Yield under load = 80 KN Maximum load = 150 KN Breaking…

Q: A combined section of steel and copper is subjected to a compressive load. Refer to the table below…

A: We will calculate stress using maximum strain.

Q: An ordinary mild steel bar has been prestressed to a working stress of 200 MPa. If the Young's…

A: Given- Initial prestress=200 MPa, Shrinkage strain = 8×10-4 E=200 GPa,

Q: A steel specimen is tested in tension. The specimen is 2 in. wide by 2.3 in. thick in the test…

Question

Explain steps

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Engineering strain of a mild steel sample is recorded as 0.100%. The true strain is 1. 2. 3. 4. 0.010% 0.055% 0.099% 0.101%
Which of the following is not a factor contributing to fatigue in a steel structure? oints) a) Repetitive tensile stress cycles b) Dead load stresses c) Microstructural damage d) Tri-axial state of stress
I need the answer as soon as possible
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :
A steel specimen having a modulus of elasticity equal to 29x103ksi has a width of 1.0in and thickness of 0.25in. During the tensile strength testing, the specimen yielded at 12.5kips and fractured at 17.5 kips. Compute the value of the tensile stresses at yield and fracture
Please solve it fast A mild steel specimen having Young’s modulus of 200 GPa and original length of 300 mm is tested for a stress of value 500 MPa. Find the resultant elongation in the specimen.
A mild steel bar has a gauge length of 80 mm and the total elongation is 0.08 mm, find the strain produced in it.
7) A specimen of steel 20 mm diameter with a gauge length of 200 mm is tested to destruction. It has an extension of 0.25 mm under a load of 80 kN and the load at elastic limit is 102 kN. The maximum load is 130 kN. The total extension at fracture is 56 mm and diameter at neck is 15 mm. Find (i) The stress at elastic limit. (ii) Young's modulus. (iii) Percentage elongation. (iv) Percentage reduction in area. (v) Ultimate tensile stress.
"Engineering Stress-Strain Curve" for a low carbon steel obtained as a result of the tensile test test. In terms of plastic forming by drawing important points on it (rolling, forging, machining ... etc.) Explain its importance.
M9
Prblm -6.
I need the answer as soon as possible