A cenuifugai pump of i.3 un deiivers 3.5 n jmin vî waier ai a ip speedof 1.5 m/s. The outlet blade angle is at 30° to the tangent at theimneller nerinhery. Assuming that the water enters the imneller radiallyand zero slip, calculate the torque delivered by the impeller?

Find the torque delivered by the impeller.

Answered: A cenurifugai pump of i.3 u deiivers…

A cenurifugai pump of i.3 u deiivers 3.5 n of 1.6 m/s. The cutlet blade angle is at 3 imneller nerinhery. Assuming that the water and zero slip, calculate the torque delivered

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: State your assumptions and justify if - 15cm necessary. a) Determine the input power of the pump to…

A: Consider the pump elevation as the datum and neglect the losses due to friction that is the major…

Q: 15. A pump delivering water at a rate of 100,000 GPM. The maximum available NPSH is 50 ft. Find the…

A: The maximum speed to avoid cavitation is 476 RPM.

Q: Problem 10.10 A hydraulic jack has a ram diameter of 20 cm and pump plunger of 4 cm diameter. The…

Q: find the pump power requirement too

Q: For ideal fluid, Find the force required to hold the blade in position, if the weight (1kN) and…

A: Given: The weight of blade, W = 1 kN The discharge, Q = 0.4 m3/s

Q: a plant installed a single-suction center fugal pump with a capacity of 300 gpm under 200 tt at 1200…

Q: A centrifugal pump having extemal and intemal diamcters as 750 mm and 400 mm respectively is…

A: Answer: (a) 16 o (b) 123 kJFor a step-by-step solution have a look through the attached pictures of…

Q: What is the crossover point in miles between thehybrid vehicle in Problem S5.4 and this alternative…

A: A vehicle that operates on alternative fuels rather than regular petroleum fuels is known as an…

Q: A pipe reducer with the pressure at A and B is 345kPa and 290 kPa respectively. the diameter at A…

Q: a reaction turbine is

A: NEED TO FIND SPECIFIC SPEED ( REACTION TURBINE)

Q: Dz 03: A centrifugal pump has an impeller with inner and outer diameters of (20 cm) and (35) cm)…

Q: A pump deliver 249 gpm of water at ahead 165m. Determine the pump power in kW

Q: In an internal gear pump, if the flow rate is 26 cm per revolution, the speed of the prime mover…

Q: A petrolengine has mechanical efficiency 0.8 and lower calorific value of ispoots 44.2 MJ/kg. The…

A: qm=0.8CV=44.2 MJ/kgbore= 0.06stroke = 0.08N=2000rpmfuel = 8liter/hW=220Nρ=750kg/m3R=400mm or…

Q: Define NPSH of a pump. What is the difference between NPSHR and NPSHA?

A: Given Data : NPSH

Q: Home work! designed. a home with PumP and calculate the Pump How to make water into tank. How to…

A: To find: Designed a home with Pump and calculate the Pump How to make water into tank. How to…

Q: Given that the compressor's energy input is 2100 kJ and the heat provided is 3500 kJ. The area is…

Q: A fous stage centrifugal pump has four ideutical empelles, keyed to the same shaft. The shaf in…

A: A device which converts mechanical energy into pressure energy with the help of centrifugal force is…

Q: To 212 F Water at 65 F flows nto a boiler at 5 gal min. It is converted to steam at 212 F Find the…

A: Given Data State 1: Saturated water, 65°F State 2: Steam, 212°F V= 5 gal/min

Q: As shown in the picture blew, a pump can deliver volume flow rate of of water through a vertical…

A: Given Flow rate, Q = 3.6 x 10-3 m3/s Density = 1000 kg/m3 Height, h = 8 m…

Q: A pico hydro turgo turbine has a torque of 0.02Nm with a rotational speed of 41 rad/s. The nozzle or…

A: The efficiency of the turbine is 47.5 %.

Q: If the head develpoed by a turbomac 15 m and the tangential velocity of th is 18 m/s, find the…

A: Given:h=15 mu=18 m/s

Q: 04: A Pelton wheel has a tangential velocity of bucket of (20 m/s). The water is being supplied…

Q: High of water in pump suction side is 8 m, neglecting of all losses, how much is the pump suction…

Q: A reaction turbine is working under a head of 10 m with an average discharge of 700 m'/min. The…

A: Given data as per question Head =10 m Average discharge =700 m3/min Overall efficiency =90%…

Q: It is desired to deliver 750 gpm at a head of 340 ft. A multistage pump will be used with a rotative…

A: Given- A multistage pump, Discharge required (Q) = 750 gpm Total head required (Ht) = 340 ft N =…

Q: -Q4:- If the wind speed measured on 10 m height from the earth. What the height of wind turbine…

A: Given Data The height from the earth surface is: h=10 m The speed of the wind is: V2=5 m/s To…

Q: A fous stage ceutrifugal pump has four ideutical empelles, keyed to Cen the scime shaft. The shaf is…

A: A device which converts mechanical energy into pressure energy with the help of centrifugal force is…

Q: What is the velocity leaving a jet engine (air) when its temperature decreases by 220C use constant…

Q: Solve fast with Proper Equation. 1. A centrifugal pump delivers 2.5 cfs of water against a head of…

Q: A Pelton wheel has diameter of 3m and develops 800KW when rotating at 200rpm. What is the average…

Q: A gear pump has gears of 40 cm outside diameter, 20 cm inside diameter and 0.0050 m width. If the…

Q: The water pump operates at (600 r.p.m) to a head (8m), the power consumption by the pump is (5 kW),…

A: Given data N = 600 rpm H = 8 m Powe consumption (P) = 5 kW overall efficiency (η) = 0.8 To…

Q: An axial pump that delivers 15 gpm, has a volumetric efficiency is 93%. Find its theoretical flow…

A: Given: actual flow rate = 15 gpm volumetric efficiency = 93%

Q: n terms of speed of the impeller N, discharge Q and change in total head H, through the machine, the…

Q: Determine the Actual Torque Required, TA

Q: A pump discharge at 60 ft at 1400 rpm. Pump is at 75% efficiency. What will be discharge at 1000 rpm

Q: centrifugal pump delivers 80 liters per second of water on test suction guage reads 10 mm Hg vacuum…

Q: then find the average velocity of the spray

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

A cenuifugai pump of i.3 un deiivers 3.5 n jmin vî waier ai a ip speed
of 1.5 m/s. The outlet blade angle is at 30° to the tangent at the
imneller nerinhery. Assuming that the water enters the imneller radially
and zero slip, calculate the torque delivered by the impeller?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A pump has overall efficiency of 70 %. It delivers 90 Ipm at 1000 rpm and 700 N/cm". If the prime mover input torque is 12 KN-cm, calculate a) the actual torque of the pump b) volumetric displacement in cm. Comment on the significance of torque in pumps. 3
Q9: Find the specific speed and power consumption for pump having the following properties: (Q=0.1 m3/s), (speed=725 r.p.m) and (head =15 m).
I need the answer as soon as possible
6. Kaplan turbine of 1 m runner diameter working under a head of 50 m. If the whirl velocity at inlet = 19 m/s and runner speed = 46.47 rad/s, the hydraulie efficiency of the turbine will be: a. 88% b. 90% c. 94% d. 97%
In a hydraulic pump, the theoretical flow rate delivered is 217 liters/min with its volumetric efficiency is 97.5%, Then find the actual flow rate in liters per second.
i need the answer quickly
If the pump needs to lift a water to an elevation of 20m from its centerline while the water source is 5m above pump centerline and the flow rate is 50 GPM, compute the motor horsepower needed if the pump efficiency is 85%. NEEDS COMPLETE SOLUTION, AS SOON AS POSSIBLE.
Q6: Calculate the specific speed for the centrifugal pump operates at (3000 r.p.m) & head of (6m) and discharge of (0.2 m3/s).
In a hydraulic pump, the theoretical flow rate delivered is 203 liters/min with its volumetric efficiency is 83.5%, Then find the actual flow rate in liters per second
A pump has a displacement of 90 cm3 . It delivers 1.25 LPS at 20 rps and 80 bar Find a) Overall efficiency of the pump b) What is the theoretical torque required to operate the pump? If prime mover input torque is 108 N-m.
EX.1 An axial flow pump with an impeller rotor diameter of 30 cm handles water at a rate of 2.7 m*/minute running at 1500 rpm. The energy input is K o W 125 J/kg and Total to Total efficiency is 0.75. If a geometrically similar pump has a diameter of 20 cm running at 3000 rpm, find its: i) Flow rate ii) input power.