i need the answer quickly JetEL. 28mAir 100kPaEL. 24mOilr.d 0.84Fig.3Q3 For ideal fluid Find the forcerequired to hold the blade in position ifthe weight 1kN and discharge 0.4msec. Answer with sketch See Fig.3

Answered: Image /qna-images/answer/e7de4d4d-160f-4e97-a97c-4ea27e1768ff.jpg

Answered: 23 For ideal fluid Find the force…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Fast pls solve this question correctly in 5 min pls I will give u like for sure Mnty If you are running 3500lbs PSI of steam thru the turbine and your governor trips at 4200 PSI. What is your percentage of increase pressure required to reach the High Limits?
35 + 9.81 (0.3824 - 7-2) = - 49.54 kPa. S. Chand e oladall i.e.Pg =- 49.54 kPa. This shows that the given pressure at A, 35 kPa is gauge pressure and hence there is vacuum at point B. (Ans.) Example 6.5. An open circuit wind tunnel draws in air from the atmosphere through a well contoured nozzle. In the test section, where the flow is straight and nearly uniform, a static pressure tap is drilled into the tunnel wall. A manometer connected to the tap shows that the static pressure within the tunnel is 45 mm of water below atmosphere. Assume that air is incompressible and at pressure is 100 kPa (absolute). Calculate the velocity in the wind tunnel section (Refer to Fig. 6.6). Density of P.= 100 kPa water is 999 kg/m' and characteristic gas constant for V =0 air is 287 J/kg K. ساP حقوق النشر 25°C, Test section = 25°C (GATE)
The water turbine of a 5-MW hydro-power plant has specific speed of 40 rpm and discharge of 2020 lps. What is the approximate diameter of the jet in mm?
A 1inch diameter nozzle there is water flows under 400ft head to operate a turbine. There is 90% efficient of turbine and connected to a 94% efficient generator. Find the power output in kilowatts.
Answer should be correct it do it if you are sure . I just need answer upto two decimal points . A jet of water of dia 10 cm strikes a flat plat normally with a velocity of 15 m/s The plate is moving with the velocity of 6m/s in the direction of jet and away from the jet . Find - 1. Force exerted by the jet on the plate.2. Workdone by the jet on plate /sec.
Fluid mechanic is our subject
Not yet answered سؤال 1 Marked out of 100.00 A closed reservoir filled by water, is under the pressure of 49 KPa as shown in the Fig.1. find the velocity of water (V) which leaves the reservoir. P=49 KPa 3m Fig.1
Solve the ff. The discharge pressure of an air compressor is 5 times the suction pressure. If the volume flow at suction is 0.7m3/s and discharge volume flow of 0.2217m3/s, what is the compressor power(hp) if suction pressure is 100kpa. Ans. 191.72 A double acting air compressor has a cylinder dimension of 50cm x 60cm, 750rpm will have a volume displacement (m3/s) of: Ans. 2.945 A pump has a specific speed of 45 and 600rpm when it delivers 0.01m3/s. Find the head developed by the pump in ft. Ans. 926.07
The pump shown is 75% efficient. If the pressure rise is 120 psi, calculate the required energy input in horsepower.
A pump has a specific speed of 45 and 600rpm when it delivers 0.01m3/s. Find the head developed by the pump in ft. Ans. 926.07
10.0 m 200 m 2. An old western town has a water tower to deliver water to the residents. Pictured above is the water tower. The water tower is closed but there is a section of air that is atmospheric pressure just above the water. The corsss ectional area at point 2 is 4.75 x 10 m. The cross sectional area fot the water tower is very large. What is the speed of the water coming out of the pipe at point 2? (density of water = kg/m³) 3. On a vacation trip up in Oregon my boys decided to build a 10 kg raft that they made out of driftwood. 1000
A centrifugal pump having an impeller of diameter 500 mm delivers 140 litres of water per sccond. The velocity of flow is 1 m/s and the vanes are curved back at outlet at 30° to the wheel tangent. If the impeller speed is 400 r.p.m., find the power to drive the pump. (Ans. 12-9 kW) 3.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

23 For ideal fluid Find the force equired to hold the blade in position if he weight 1kN and discharge 0.4m rotnh Anower with okotoh See Fig 2