A cast iron link, as shown in Fig. 4.4, is required to transmit a steady tensile loadof 45 kN. Find the tensile stress induced in the link material at sections A-A and B-B.BAB40 75→|20-니20-BAВSection at B-BAll dimensions in mm.

Answered: Image /qna-images/answer/6c4dfd70-a18e-48b1-b4c1-0c18f6a20564.jpg

Answered: A cast iron link, as shown in Fig. 4.4,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

very small SMOoth pulley Q2/ Determine the load (W) for the bar (ABCD) shown in Fig.I which is supported (250mm')cable with very siall sioth pulley and vertical (300mm?) cable at (C) and a horizontal roller at (D), The stress in all cables is limited to 150MPA. at (A) and (B) by 45° 3.0rm 1.Om 1 On
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.29 mm the values of elastic modulus for steel is 217 MPa. Take H1 = 4 cm, H2 = 11 cm, top bar (R) is 3 x 3 cm and bottom bar (Q) is 7 x 7 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P = ii) Stress-induced in the top bar = iii) Stress-induced in the bottom bar =
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.66 mm the values of elastic modulus for steel is 207 MPa. Take H1 = 4 cm, H2 = 11 cm, top bar (R) is 3 x 3 cm and bottom bar (Q) is 7 x 7 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P = (in N) ii) Stress-induced in the top bar = (in N/mm^2) iii) Stress-induced in the bottom bar = (in N/mm^2)
PLEASE EXPLAIN
The composite bar in Fig. P-247 is stress-free before the axial loads P, and P₂ are applied. Assuming that the walls are rigid, calculate the stress in each material if P₁ = 150 kN and P2₂ = 90 kN. Aluminum Steel A = 900 mm² A = 2000 mm² E = 70 GPa E 200 GPa P 500 mm Bronze A = 1200 mm² E = 83 GPa 250 mm 350 mm Figure P-247 and P-248
A brass pipe has an internal diameter of 400mm and a metal thickness of 6mm. A single layer of high tensile wire of diameter 3mm is wound closely around it at a tension of 500N. Find the stress in the pipe when there is no internal pressure. (b) the maximum permissible internal pressure in the pipe if the working tensile stress in the brass is 60MN/m^2. (c)) The stress in the steel wire under condition b. Treat the pipe as thin cylinder and neglect longitudinal stresses and strains. Young mudulus of steel=200GN/m^2 and for brass =100GN/m^2
SHOW ILLUSTRATION AND SOLUTION Problem 1: A steel rod with a cross - sectional area of 150 mm2 is stretched between 2 fixed supports. The tensile load at 20 oC is 5 kN. Use E = 200 GPa and  = 11.7 x 10- 6 /oC 1. At what temperature will the stress be zero?2. What will be the stress at - 20
Problem #3 Three rods, each of area 200 mm², jointly support a 7.5 kN load, as shown in the figure. Assuming that there was no slack or stress in the rods before the load was applied, find the stress in each rod. Use Est = 200 GPa and Ebr = 83 GPa. Sted 7.5 KN 2.75 m
The Uniform AB brass bar is fixed with support and pin as shown in the figure and has a rectangular perpendicular cross-sectional area. Both ends of the bar are free in the vertical direction, but are prevented from rotating in the horizontal direction. a- Find b/d ratios at safe limits for horizontal and vertical axes. b- If P= 1,8 kN, L= 7 m, d= 60 mm and e= 150 GPa, what is the safety factor?
Design of machine elements solve according to Khurmi Please write clearly
4. A steel rod of length L and uniform cross sectional area A is secured between two walls, as shown. Use L=1.7 m, E = 200 GPa, a = 11.9 × 10-6 /°C and AT = 70 °C. Calculate the stress for a temperature increase of AT for: a) The walls are fixed. b) The walls move apart a distance 0.4 mm. (20 pts)
(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A cast iron link, as shown in Fig. 4.4, is required to transmit a steady tensile load f 45 kN. Find the tensile stress induced in the link material at sections A-A and B-B. B В