A CAST IRON COLUMN OF CIRCULAR SECTION HAS A PROJECTING BRACKET CARRYING A LOAD OF 200 KN AT A DISTANCE 350 MM FROM THE AXIS OF COLUMN . IF EXTERNAL AND INTERNAL DIAMETER OF COLUMN ARE 300 MM AND 250 MM RESPECTIVELY . FIND THE MAXIMUM AND MINIMUM STRESSES IN SECTION.

A CAST IRON COLUMN OF CIRCULAR SECTION HAS A PROJECTING BRACKET CARRYING A LOAD OF 200 KN AT A DISTANCE 350 MM FROM THE AXIS OF COLUMN . IF EXTERNAL AND INTERNAL DIAMETER OF COLUMN ARE 300 MM AND 250 MM RESPECTIVELY . FIND THE MAXIMUM AND MINIMUM STRESSES IN SECTION.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

H.W No.1: The concrete I-beam of figure is pretensioned with four bounded stranded cables having total area (371 mm²). Eccentricity of the steel varies parabolically from 0 at the support to 193 mm at the center of 9 m span. The effective stress in steel after losses is 910 MPa. 254 mm 102 mm 76 mm 102 mm 193 mm 9 m a-what superimposed load will produce a balanced condition of external equivalent prestress load, such that uniform axial compression will be obtained in the concrete. b-what superimposed uniform distributed load will produce cracking of the beam, given the modulus of rupture f=3.28 MPa. c-compute the flexural strength of the beam and compare with the cracking moment. Use: fe = 27.6 MPa, fpy= 1469 MPa, fpu= 1724 MPa. Aps fps a= 0.85 feb --) M₁ = Aps fps (dp- Mn Mn = Pp fps bdp² (1 -0.59 x P x Ips) fci Apf = 0.85 f (b-bw)h fps Apw = 0.85 bw a fps a= Apwfps 0.85 fobw
c) The three suspender bars are made of A-36 steel and have equal cross-sectional areas of 450 mm² .Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown. A B C 80 kN 2 m 50 kN D E F -1m--1m--1 m--1m-|
The concrete column is reinforced using four steelreinforcing rods, each having a diameter of 25 mm.Determine the stress in the concrete and the steel if thecolumn is subjected to an axialload of 1200 kN. Est = 200 GPa,Ec = 25 GPa.
Need answer and full solution ASAP. Thanks
2 - please provide a clear and complete solution, thanks!
A rectangular cantilever beam has a width of 300mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The magnitude of the Ultimate moment capacity is Blank 1kN.m.
A 3-m long steel column of hollow circular cross-section is supported on a steel base plate and a concrete pedestal. Column ends are hinged and sidesway is prevented.the outside diameter of the column is 260 mm, allowable compressive stress is 55 MPa and the allowable concrete bearing stress is 10 Mpa.40. Compute the required thickness of the column tio support axial load of 800 Kn.A. 18 mm B. 19 mm C.20 mm D. 10mm41. Compute for the minimum required diameter of the base plate.A. 300 mm B. 320 mm C.350 mm D. 280 mm42. If the thickness of column is 10mm, find the critical slenderness ratio.A. 33.914 B. 45.871 C.87.876 D. 23.811
B4
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is inclined I V : 4 H and distance between trusses is equal to 6 m. The purlin has a weight of 79 N/m and spaced at 1.2 m. on centers. The dead load including the roof materials is 720 Pa, live load of 1000 Pa and wind load of 1.2 1.2 1440 Pa. Coefficient of Purlins pressure at leeward and windward are 0.6 and 0.2 respectively. Assume all loads passes through the centroid of the section. Properties of C 200 x 76 mm Sx = 6.19 x 104 mm Sy = 1.38 x 104 mm3 W = 79 N/m 1.2 Truss 1.2 12 12 1.2 Allowable bending stress Fbr = Fby = 207 MPa Truss %3D 6m O Calculate the bending stress, fox, for dead load and live load combination (D + L). Calculate the bending stress, foy, for dead load and live load combination (D + L). O Calculate the maximum ratio of actual to the allowable bending stress for load combination 0.75 (D + L + W) at the windward side. fbx = 151.14 MPa fby = 169.6 MPa Interaction = 1.25
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is inclined I V: 4 H and distance between trusses is equal to 6 m. The purlin has a weight of 79 N/m and spaced at 1.2 m. on centers. The dead load including the roof materials is 720 Pa, live load of 1000 Pa and wind load of 1.2 1.2 1440 Pa. Coefficient of Purlins pressure at leeward and windward are 0.6 and 0.2 respectively. Assume all loads passes through the centroid of the section. Truss Properties of C 200 x 76 mm Sx = 6.19 x 104 mm Sy = 1.38 x 104 mm W = 79 N/m 12 12 1.2 I Allowable bending stress Fbx= Fby = 207 MPa Truss %3D 6m O Calculate the bending stress, fox, for dead load and live load combination (D+ L). Calculate the bending stress, foy, for dead load and live load combination (D + L). O Calculate the maximum ratio of actual to the allowable bending stress for load combination 0.75 (D + L + W) at the windward side. fbx = 151.14 MPa fby = 169.6 MPa Interaction = 1.25
Determine the force in member FE of the truss below. Indicate as positive if the member is in tension and negative (-) if the member is in compression. Provide the answer in kN G 3 m E A B D -2 m- -2 m- -2 m. 5 kN 5 kN 5kN ⋅ Previous с 。 4 Q Search securySearch % 5 & 7 8 9
A continuous wood stave pipe is 3.0 m in diameter and is in service under a head of 30.0 m of water. The staves are secured by means of round 25mm steel hoops with an allowable stress of 105 MPa. Find the maximum spacing of the hoops to safely secure the pipe. Assume that there is an initial tension of 7,000 n applied to the hoops.