"A carpet manufacturing company is comparing the tensile strengths of two different types of synthetic fiber. Synthetic fiber A used in manufacturing carpet has tensile strength that is normally distributed with mean 75 psi and standard deviation 8 psi, and synthetic fiber B has tensile strength that is 75 psi and standard deviation 12 psi. Random sample of nA = 16 and nB = 9 of fiber specimens are selected. Find the probability that the sample mean of fiber specimen A exceeds the sample mean of fiber specimen B by 4."

"A carpet manufacturing company is comparing the tensile strengths of two different types of synthetic fiber. Synthetic fiber A used in manufacturing carpet has tensile strength that is normally distributed with mean 75 psi and standard deviation 8 psi, and synthetic fiber B has tensile strength that is 75 psi and standard deviation 12 psi. Random sample of nA = 16 and nB = 9 of fiber specimens are selected. Find the probability that the sample mean of fiber specimen A exceeds the sample mean of fiber specimen B by 4."

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Asiacell 4,ll ON 76% D19:17 سؤال الواجب.docx Problem :- The following data was obtained tensile test on a specimen of 6 mm diameter and gauge length Lo=30 mm: load(KN) 0 40 80 95 90 135 150.2 145 130 120 elongation(mm) 0 0.022 0.13 0.25 0.55 2.01 3.88 4.12 5.22 6 Plot engineering and True (stress-strain) curves, then determine the (oy, ɛy), (ou, ɛu), (of, , ef), ductility , modulus of elasticity . Then select on the drawing (strain hardening (n)), (Necking), (uniform plastic region and non-uniform plastic region) and (elastic & plastic) region)?
(B); Consider the instrument of Electrical Resistance Strain Gage shown in the Figure 2, and answer the following questions: 1. Is the instrument considered as a passive or an active transducer? Clarify your answer with diagram. 2. What are the functions should be carried out by the strain gage and the Wheatstone bridge? 3. Which method of corrections should be used to nullify and reduce the errors that may be existed by 0.1 Test Specimen Strain Gage Figure 2. 60 Ma Field 11 Wheatstune Bridge
Correct and complete solution please
1- what materials are included here (z parameter), type of materials considered, property or properties plotted, domain of c, parameter identified 2- what are the vertical and horizontal trends presented 3-what is the take away story from this plot please answer i will upvote
A cylindrical sample of a biological product (10. mm in diameter and 18 mm in height) was exposed to a constant strain test. Assume that the stress in the sample can be described using Standard linear model. The axial load applied to the sample at time zero was 80. N and then after the infinitely long time the force equilibrated 20. N. The viscosity coefficient of the viscous element in the Maxwell arm is 7.50 x103 kPas, and the modulus of elasticity of the elastic element in the Maxwell arm is 15 kPa. Determine after what time the compression force will decrease to 36% of its original value and the modulus of elasticity of the elastic element in the equilibrium arm.
A structural component in the form of a wide plate is to be fabricated from a steel alloy that has a plane strain fracture toughness of 88 MPam (ksi √/in.)) and a yield strength of 880 MPa (63820 psi). The flaw size resolution limit of the flaw detection apparatus is 3 mm (0.1181 in.). (a) If the design stress is one-half of the yield strength and the value of Y is 1.11, what is the critical flaw length? i mm (b) On the basis of this value, is a critical flaw subject to detection?
1. For the stress-strain curve shown below, please estimate the properties indicated. (a) Fracture Strain Please do your work on a separate sheet of paper, and put your answers in the boxes on the right. Be sure to include the proper symbol and units. Stress Strain 70 60 50 Stress (ksi) 240 30 20 10 70 0 0.000 60 50 Stress (ksi) 40 20 10 KULL 0 0.000 0.010 0.050 0.100 Strain (in/in) Stress Strain 0.020 0.030 Strain (in/in) 0.040 0.150 0.050 (b) Ultimate Tensile Stress (c) Fracture Stress (d) Proportional Limit (e) Elastic Modulus (1) Yield Stress (g) Tensile Toughness (Modulus of Toughness) (h) Modulus of Resilience
Compare and discuss the results. Determine the experimental shear modulus of elasticity. TORSION TEST EXPERIMENT
You have been given the following test sample data following mechanical testing of 15 test pieces of Silicon Nitride. What is the Weibull modulus of this material? Would you advise the use of a similar material with a Weibull Modulus of 16.3 and a mean failure stress of 485 MPa, if you anticipate that the peak stress on the material could be 430 MPa? Sample 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Select one or more: O a. No O b. 18.6 O C. 13.4 O d. Yes O e. 15.7 f. 17.1 Failure Stress (MPa) 423 459 496 432 447 467 473 499 485 479 505 530 526 490 510 <
Give me right solution.. please help me urgent
Problem 24.17 A mechanical component is subjected to a mean stress of 100 N/mm and a standard deviation of 10 N/mm. The material of the component has a mean strength of 130 Nhmm and a standard deviation of 15 N/mm. () Find the probability of fallure for the соmponent. (ii) If better mamufaeturing control reduces the standard deviation of material strength to 10 N/mm?, find the probability of failure. (iii) If we consider only mean values of the data in design, find out the factor of safety:
True/False The self-preserving size distribution for particles undergoing thermal coagulation generally has a geometric standard deviation of about 1.3.