The following data was obtained from a tensile test on Load (kN) Extension (mm) 16 32 56 72 95 110 132 142 140 135 0.2 0.4 0.7 0.9 1.5 2.5 5.0 8.5 10.0 12.0 a specimen of 10mm diameter and gauge length 60mm. Using the graph paper supplied, plot the load-extension diagram and determine: (1) The tensile strength (2) 0.1% Proof Stress (3) Young's Modulus for the specimen

The following data was obtained from a tensile test on Load (kN) Extension (mm) 16 32 56 72 95 110 132 142 140 135 0.2 0.4 0.7 0.9 1.5 2.5 5.0 8.5 10.0 12.0 a specimen of 10mm diameter and gauge length 60mm. Using the graph paper supplied, plot the load-extension diagram and determine: (1) The tensile strength (2) 0.1% Proof Stress (3) Young's Modulus for the specimen

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Explain about these graphs and discuss how they are helpful in engineering. (TENSILE TEST)
What is the Young’s modulus in GPa
Pressure distribution measurements are made on a two-dimensional wing model placed in a wind tunnel. The difference between the static pressure sockets on the surface and the static pressure of the free stream is measured. 30 data is taken at each measurement point. The average of the values measured from one of the sockets near the trailing edge was calculated as 2.30 Pa, and the standard deviation was calculated as 2.65 Pa. After applying the Chauvenet criterion to these measurement values, it was decided to eliminate 3 measurements and the new mean value was found to be 2.18 Pa and the standard deviation was 2.42. It was verified that the unexcluded data fit the normal distribution curve. Data above how many Pa and below how many Pa were eliminated? Estimate how many data have negative value (?<0) after elimination.
mecha
From the data what is the materials ultimate strength in MPa
Creep exercises The following data in the table below was obtained a from rupture test. Stress (MPa) Temperature (°C) Rupture time (hr) T 550 580 0.75 550 555 5.5 550 540 19.2 550 525 62.0 70 760 2.05 70 730 8.2 70 700 36.5 70 675 134 Assume: C = 46 Establish whether the Larson-Miller parameter is valid for both stresses (550 and 70 MPa). Was there a change in creep mechanism when changing the stress from 550 to 70 MPa during rupture test? Motivate your answer with the aid of calculation.
A beam subjected to a bending moment undergo a normal stress. A study was done and a sample was obtained with the following statistical parameters: Mean stress value = 452 MPa Value of the standard distribution = 21.4 MPa. The beam is made of steel with: Mean value of yield strength = 540 MPa Value of the standard distribution of yield strength = 38.4 MPa. If the strength and stress have normal distributions, determine the reliability in % considering yielding.
A tension test was performed on a specimen having an original diameter of 13.7 mm and a gauge length of 50 mm. The data are listed in the table. Load (kN) Elongation (mm) 0 11.1 31.9 37.8 40.9 43.6 53.4 62.3 64.5 62.3 58.8 0 0.0175 0.0600 0.1020 0.1650 0.2490 1.0160 3.0480 6.3500 8.8900 11.9380 Plot the stress-strain diagram. Use a scale of 20 mm = 50 MPa and 20 mm = 0.05 mm/mm. Redraw the linear-elastic region, using the same stress scale but a strain scale of 20 mm = 0.001 mm/mm. From the diagram, determine approximately the modulus of elasticity. Express your answer to three significant figures and include the appropriate units. E = Submit Part B συ = Submit Part C ☐☐ μÅ of = Value Determine the ultimate stress. Express your answer to three significant figures and include the appropriate units. Request Answer μĂ Value Request Answer Units μĂ - Value Units Determine the fracture stress. Express your answer to three significant figures and include the appropriate units. ? Units ? ?
. 2) A following figure and table display creep test data obtained from a uniaxial specimen having an initial gauge length of 2 cm. Calculate the steady-state creep rate. Length |(cm) 2.3 Time | (h) 2.25 2.004 2.2 100 2.010 200 2.020 400 2.030 1000 2000 2.045 2.075 2.1 2.05 4000 2.135 6000 2.193 7000 2.230 1.95 8000 2.300 1000 2000 3000 4000 5000 6000 7000 8000 Time (h) (rupture) | Length between the gauge marks (cm) 2.
A test rod of rust-resistant steel, with a diam. of 12.8 mm and a measuring length of 50.8 mm is subjected to a tensile test. The data from the test is shown in the table below.
Data taken from a tensile test is given below. The curve is linear between the origin and the first point. The gauge length is 34 mm and the cross sectional area is 12.56 mm2. Determine the modulus of elasticity. Force (N) Extension (mm) 7000 0.25 8000 0.32 8500 0.56 8500 0.7 Select one: O a. none of these options O b. 75.8 GPa O c. 109.5 GPa O d. 305 GPa O e. 201.6 MPa O f. 240 MPa O g. 86.3 GPa O h. 102 GPa
You have been given the following set of data from a soil-geotextile friction test: Normal stress (kPa) Peak shear strength (kPa) Residual shear strength (kPa) 17 20.2 13 35 31 22 70 52 39.5 140 94 74.5 (a) Plot the Mohr-Coulomb failure envelope (x-axis=normal stress; y-axis=shear stress) (b) Determine the peak friction angle, and the residual friction angle, . (c) Determine the peak adhesion and the residual adhesion. (d) Calculate the fabric efficiency based on a soil friction angle of = 35-degrees using the peak friction angle. **HINT: the equation for efficiency of soil friction angle mobilization is: