A Carnot vapor power cycle operates with water as the working fluid. Saturated liquid enters the boiler at 1000 lbf/in.², and saturatedvapor enters the turbine (state 1). The condenser pressure is 1.2 lbf/in.² The mass flow rate of steam is 1 x 106 lb/h. Data at key pointsin the cycle are provided in the accompanying table.Determine:State p (lbf/in.²) h (Btu/lb)123410001.21.210001192783.4416.3542.5(a) the percent thermal efficiency.(b) the back work ratio.(c) the net power developed, in Btu/h.(d) the rate of heat transfer to the working fluid passing through the boiler, in Btu/h.

Given:Pressure at boiler inlet, Pb=1000 lbf/in2Condenser pressure, Pc=1.2 lbf/in2At turbine…

A Carnot vapor power cycle operates with water as the working fluid. Saturated liquid enters the boiler at 1000 lbf/in.2, and saturat vapor enters the turbine (state 1). The condenser pressure is 1.2 lbf/in.² The mass flow rate of steam is 1 x 106 lb/h. Data at key poin in the cycle are provided in the accompanying table. State p (lbf/in.²) 1 2 3 1000 1.2 1.2 h (Btu/lb) 1192 783.4 416.3

A Carnot vapor power cycle operates with water as the working fluid. Saturated liquid enters the boiler at 1000 lbf/in.2, and saturat vapor enters the turbine (state 1). The condenser pressure is 1.2 lbf/in.² The mass flow rate of steam is 1 x 106 lb/h. Data at key poin in the cycle are provided in the accompanying table. State p (lbf/in.²) 1 2 3 1000 1.2 1.2 h (Btu/lb) 1192 783.4 416.3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is the working fluid in a Rankine cycle. Steam exits the steam generator at 1500 lbf/in.2 and 1100°F. Due to heat transfer and frictional effects in the line connecting the steam generator and turbine, the pressure and temperature at the turbine inlet are reduced to 1400 lbf/in.² and 1000°F, respectively. Both the turbine and pump have isentropic efficiencies of 90%. Pressure at the condenser inlet is 2 lbf/ in.2, but due to frictional effects the condensate exits the condenser at a pressure of 1.5 lbf/in.² and a temperature of 110°F. The condensate is pumped to 1600 lbf/in.² before entering the steam generator. The net power output of the cycle is 5.5 x 108 Btu/h. Cooling water experiences a temperature increase from 60°F to 76°F, with negligible pressure drop, as it passes through the condenser. Determine for the cycle: (a) the mass flow rate of steam, in lb/h. (b) the rate of heat transfer, in Btu/h, to the working fluid passing through the steam generator. (c) the percent…
A Rankine steam cycle modified for reheat and three closed feedwater heaters is shown below. The high-pressure turbine receives 80 kg/s of steam from the steam boiler. The feedwater heater exit states for the boiler feedwater and the condensed steam are the normally assumed ideal states. The following data tables give the saturation data for the pressures and data for h and s at selected states. Take cp, water = 4.18 kJ/kg·K. Process states and selected data State P, kPa T, °C h, kJ/kg s, kJ/kg·K 1 10 2 5000 3 5000 4 5000 5 5000 6 5000 7 5000 700 3900 7.5136 8 2500 3615 7.5136 9 2500 600 3687 7.5979 10 925 3330 7.5979 11 300 3011 7.5979 12 75 2716 7.5979 13 10 2408 7.5979 Saturation data P, kPa T, °C vf, m3/kg hf, kJ/kg sf, kJ/kg·K 10 45.8 0.001010 191.8 8.149 75 91.8 0.001037 384.4 7.456 300 133.5 0.001073 561.4 6.992 925 176.5 0.001123 747.7 6.612 2500 224.0 0.001197 961.9 6.256 5000…
(a) Steam is supplied, dry saturated at 40 bar to a turbine and the condenser pressure is 0.035 bar. If the plant operates on the Rankine cycle, calculate, per kilogram of steam: (i) the work output neglecting the feed-pump work; (ii) the work required for the feed pump: (iii) the heat transferred to the condenser cooling water, and the amount of cooling water required through the condenser if the temperature rise of the water is assumed to be 5.5 K; (iv) the heat supplied; (v) the Rankine efficiency; (vi) the specific steam consumption. (b) For the same steam conditions calculate the efficiency and the specific steam consumption for a Carnot cycle operating with wet steam. (C) Repeat Problem (a) for a steam supply condition of 40 bar and 350 °C and the same condenser pressure of 0.035 bar.
2.2
Steam at 4800 lbf/in.2, 1000 deg F enters the first stage of a supercritical reheat cycle including two turbine stages. The steam exiting the first-stage turbine at 600 lbf/in.2 is reheated at constant pressure to 1000 deg F. Each turbine stage and the pump have an isentropic efficiency of 85%. The condenser pressure is 1 lbf/in.2 If the net power output of the cycle is 100 MW, determine (a) the rate of heat transfer to the working fluid passing through the steam generator, in MW. (b) the rate of heat transfer from the working fluid passing through the condenser, in MW. (c) the cycle thermal efficiency.
! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The net work output and the thermal efficiency for the Carnot and the simple ideal Rankine cycles with steam as the working fluid are to be calculated and compared. Steam enters the turbine in both cases at 5 MPa as a saturated vapor, and the condenser pressure is 50 kPa. In the Rankine cycle, the condenser exit state is saturated liquid and, in the Carnot cycle, the boiler inlet state is saturated liquid. Draw the T-s diagrams for both cycles. (Please upload your response/solution using the controls below. You must provide an answer before moving on to the next part.)
3. A gas turbine uses the Joule cycle. The inlet pressure and temperature to the compressor are respectively 1 bar and -10°C. After constant pressure heating, the pressure and temperature are 7 bar and 700°C respectively. The flow rate of air is 0.4 kg/s. Calculate the following. 1. The cycle efficiency. 2. The heat transfer into the heater. 3. the net power output. y= 1.4 Cp = 1.005 kJ/kg K %3D
2. PLEASE ANSWER ASAP
Instructions: solve problems under the concept of Reheat, Regenerative and Reheat-Regenerative Cycle in Rankine cycles (set the values to 4 decimal places for consistency) Review Questions (M.1) Steam at 10 MPa, 600 °C enters the first-stage turbine of an ideal Rankine cycle with reheat. The steam leaving the reheat section of the steam generator is at 500 °C, and the condenser pressure is 6 kPa. If the quality at the exit of the second stage turbine is 90%, determine a) the mass flow rate of the steam in kg/h and b) thermal efficiency (%) of the cycle c) mass of the cooling water in kg/ h, if the temperature rise in the cooling water is 20 °C.
1.10Water is the working fluid in a reheat-regenerative Rankine cycle with one closed feedwater heater and one open feedwater heater. Steam enters the turbine at 1400 lbf/in.2 and 1000°F and expands to 500 lbf/in.2, where some of the steam is extracted and diverted to the closed feedwater heater. Condensate exiting the closed feedwater heater as saturated liquid at 500 lbf/in.2 undergoes a throttling process to 120 lbf/in.2 as it passes through a trap into the open feedwater heater.The feedwater leaves the closed feedwater heater at 1400 lbf/in.2 and a temperature equal to the saturation temperature at 500 lbf/in.2 The remaining steam is reheated to 900°F before entering the second-stage turbine, where it expands to 120 lbf/in.2 Some of the steam is extracted and diverted to the open feedwater heater operating at 120 lbf/in.2 Saturated liquid exits the open feedwater heater at 120 lbf/in.2The remaining steam expands through the third-stage turbine to the condenser pressure of 3.5…
Question 3 of 15 Water is the working fluid in a Rankine cycle. Steam exits the steam generator at 1500 lbf/in.2 and 1100°F. Due to heat transfer and frictional effects in the line connecting the steam generator and turbine, the pressure and temperature at the turbine inlet are reduced to 1400 lbf/in.2 and 1000°F, respectively. Both the turbine and pump have isentropic efficiencies of 85%. Pressure at the condenser inlet is 2 lbf/ in.2, but due to frictional effects the condensate exits the condenser at a pressure of 1.5 lbf/in.² and a temperature of 110°F. The condensate is pumped to 1600 lbf/in.2 before entering the steam generator. The net power output of the cycle is 1 x 10 Btu/h. Cooling water experiences a temperature increase from 60°F to 76°F, with negligible pressure drop, as it passes through the condenser. (a) the mass flow rate of steam, in lb/h. (b) the rate of heat transfer, in Btu/h, to the working fluid passing through the steam generator. (c) the percent thermal…
A binary vapour cycle operates on mercury and steam. Standard mercury vapour at 4.5 bar is supplied to the mercury turbine, from which it exhausts at 0.04 bar. The mercury condenser generates saturated steam at 15 bar which is expanded in a steam turbine to 0.04 bar. (1) Determine the overall efficiency of the cycle. (ii) If 48000 kg/h of steam flows through the steam turbinc, what is the flow through the mercury turbine ? (ii) Assuming that all processes are reversible, what is the useful work donc in the binary vapour aycle for the specified steam flow ? (iv) If the steam leaving the mercury condenser is superhecated to a temperature of 300°C in a superhcater located in the mercury boiler and if the internal efficiencies of the mercury and steam turbines are O.84 and 0.88 respectively, calculate the overall efficiency of the cycle. The properties of standard mercury are given below : hfkJlkg) h,(kJlkg) sp (kJlkg K) §, (kJkg K) v, (m³Ihg) v, (m³Ikg) 0.5397 p (bar) t (°C) 4.5 450 62.93…