A Carnot vapor power cycle operates with water as the working fluid. Saturated liquid enters the boiler at 1400 lbf/in.?, and saturated vapor enters the turbine (state 1). The condenser pressure is 1.2 Ibf/in.2 The mass flow rate of steam is 1 x 10’ lb/h. Data at key points in the cycle are provided in the accompanying table. State p (lbf/in.2) h (Btu/lb) 1 1400 1174 2 1.2 758.3 3 1.2 446.5 4 1400 598.8

A Carnot vapor power cycle operates with water as the working fluid. Saturated liquid enters the boiler at 1400 lbf/in.?, and saturated vapor enters the turbine (state 1). The condenser pressure is 1.2 Ibf/in.2 The mass flow rate of steam is 1 x 10’ lb/h. Data at key points in the cycle are provided in the accompanying table. State p (lbf/in.2) h (Btu/lb) 1 1400 1174 2 1.2 758.3 3 1.2 446.5 4 1400 598.8

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.9Water is the working fluid in a regenerative Rankine cycle with one closed feedwater heater and one open feedwater heater. Steam enters the turbine at 1400 lbf/in.2 and 1150°F and expands to 500 lbf/in.2, where some of the steam is extracted and diverted to the closed feedwater heater. Condensate exiting the closed feedwater heater as saturated liquid at 500 lbf/in.2 undergoes a throttling process to 120 lbf/in.2 as it passes through a trap into the open feedwater heater.The feedwater leaves the closed feedwater heater at 1400 lbf/in.2 and a temperature equal to the saturation temperature at 500 lbf/in.2 The remaining steam expands through the second-stage turbine to 120 lbf/in.2, where some of the steam is extracted and diverted to the open feedwater heater operating at 120 lbf/in.2 Saturated liquid exits the open feedwater heater at 120 lbf/in.2The remaining steam expands through the third-stage turbine to the condenser pressure of 5 lbf/in.2 The turbine stages and the pumps each…
STEP 4 PLS
An Ideal rankine cycle steam (7 MPa, 10kPa).Ideal Rankine vapor power cycle operates with steam.Saturated vapor enters the turbine at 7 MPa.The condenser pressure is 10 kPa. Determine thea. turbine work, in kJ/kgb. Condenser heat transfer, in kJ/kgc. Pump work, in kJ/kgd. boiler heat transfer, in kJ/kge. thermal efficiencyf. back work ratio
Water is the working fluid in a Rankine cycle. Steam exits the steam generator at 1500 lbf/in.2 and 1100°F. Due to heat transfer and frictional effects in the line connecting the steam generator and turbine, the pressure and temperature at the turbine inlet are reduced to 1400 lbf/in.² and 1000°F, respectively. Both the turbine and pump have isentropic efficiencies of 95%. Pressure at the condenser inlet is 2 lbf/ in.2, but due to frictional effects the condensate exits the condenser at a pressure of 1.5 lbf/in.² and a temperature of 110°F. The condensate is pumped to 1600 lbf/in.² before entering the steam generator. The net power output of the cycle is 5.5 x 108 Btu/h. Cooling water experiences a temperature increase from 60°F to 76°F, with negligible pressure drop, as it passes through the condenser. Determine for the cycle: (a) the mass flow rate of steam, in lb/h. (b) the rate of heat transfer, in Btu/h, to the working fluid passing through the steam generator. (c) the percent…
In a Rankine cycle steam enters the turbine at 2.5MPa (enthalpies and entropies given) and condenser of 50KPa (properties given), what is the thermal efficiency of the cycle? At 2.5MPa: hg = 2803.1 sg = 6.2575, At 50KPa: sf = 1.0910 sfg = 6.5029 hf = 340.49 hfg = 2305.4 vf = 0.0010300
Boiler High-P turbine LOW-P turbine Reheater 4 P₁ = P5 = Preheat P4 2 Pump Condenser 1 The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 °C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m³/kg Find the specific entropy in kJ/kg at state 1 to 3 decimal places.
Please answer a,b,c. Badly needed. Thank you.
letters d and e
Water is the working fluid in an ideal Rankine cycle. Steam enters the turbine at 1400 lb/in² and 1000°F. The condenser pressure is 2 Ib;/in.² The net power output of the cycle is 250 MW. Cooling water experiences a temperature increase from 60°F to 76°F, with negligible pressure drop, as it passes through the condenser. Step 1 Determine the mass flow rate of steam, in lb/h. m = i lb/h
2.11
Water is the working fluid in a Rankine cycle. Steam exits the steam generator at 1500 lbf/in.² and 1100°F. Due to heat transfer and frictional effects in the line connecting the steam generator and turbine, the pressure and temperature at the turbine inlet are reduced to 1400 lbf/in.² and 1000°F, respectively. Both the turbine and pump have isentropic efficiencies of 85%. Pressure at the condenser inlet is 2 lbf/ in.², but due to frictional effects the condensate exits the condenser at a pressure of 1.5 lbf/in.² and a temperature of 110°F. The condensate is pumped to 1600 lbf/in.² before entering the steam generator. The net power output of the cycle is 1x 10⁹ Btu/h. Cooling water experiences a temperature increase from 60°F to 76°F, with negligible pressure drop, as it passes through the condenser. Determine for the cycle: (a) the mass flow rate of steam, in lb/h. (b) the rate of heat transfer, in Btu/h, to the working fluid passing through the steam generator. (c) the percent…