A cantilever wood pole carries force P= 300 N applied at its free end, as well as its own weight (weight density = 6 kN/m3). The length of the pole is L = 0.75m and the allowable bending stress is 14 MPa. The required diameter of the pole is approximately: (A) 4.2 cm (B) 5.5 cm (С) 6.1 сm (D) 8.5 cm B L-

A cantilever wood pole carries force P= 300 N applied at its free end, as well as its own weight (weight density = 6 kN/m3). The length of the pole is L = 0.75m and the allowable bending stress is 14 MPa. The required diameter of the pole is approximately: (A) 4.2 cm (B) 5.5 cm (С) 6.1 сm (D) 8.5 cm B L-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 2: Two-pinned connected bars supported the rigid member BC as shown. A vertical load of 25 KN is applied to BC at a distance x from bar AB. What should be the distance x to make the stresses in two bars the same? The area of bar AB is 100 mm² and of bar CD is 150 mm². A 8 600 mm P= 25 KN D
The steel truss with E=200GPais loaded as shown in the figure. Determine the following: the following a) the deformation of member AB if the cross-sectional area is 2500mmb) the deformation of member AD if the cross-sectional area is 1800mm A 4.0m 200 KN B D 4.0m 1² 2.5m
A rigid plate C is used to transfer a 20-kip load P to a steel (E = 30,000 ksi) rod A and to an aluminum alloy (E = 10,000 ksi) pipe B as shown. The supports at the top of the rod and the bottom of the pipe are rigid, and the materials were unstressed before the load was applied. The cross-sectional areas of rods A and pipe B are 0.80 in2 and 3.00 in2 respectively. Determine The normal stress in rod A in ksi, The normal stress in pipe B in ksi and The displacement of plate C in inches. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 5 decimal places.
Solve using Method of Consistent Deformation
A = 300 mm² A = 150 mm² E D P. •B 0.2 m| 0.2 m| 0.2 m| 0.2 m For the steel bar and loading shown in the figure, assuming that both supports are fully seated before the loads are applied, we remove the reaction at (a) E, and the absolute value of the deformation caused by the loads P1 = 629 kN and P2 = 340 kN | SL| (b) the absolute value of the reaction force at E | RE| In kN units, (c) the absolute value of the reaction force at A |RA| Specify in kN units. For steel, use E = 200 GPa.
Experts Pleae help ASAP
A simply supported beam is loaded by the couple M=2000 N-m as shown. The beam has a channel-type cross section as illustrated. 3 cm 30 cm 3 cm 3 m -2m1 10.5 cm BI 12 cm M. Determine the maximum tensile stress in the beam. O 1.60 MPa 3.73 MPa )2.49 MPa O1.07 MPa Determine the maximum compressive stress in the beam. 3.73 MPa O 1.07 MPa 2.49 MPa O 1.60 MPa Determine the maximum shear stress in the beam. O 00588 MPa 0.0490 MPa 0.0653 MPa O 0.0667 MPa
0.1 m Q4) Determine the maximum tensile and compressive bending stress in the beam shown in Figure (4), if it is subjected to a positive moment of M=20 kN.m 0.3 m N- 0.1 m Figure (4) -0.2 m- (1
Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. 0.4 m 0.5 m B 20-mm diameter 60-mm diameter 1. Determine the deformation at segment AB in millimeter if P = 58 kN and Q = 0.
A rigid bar AB is hinged at A and supported by copper rod 2 m long and steel rod i m long as shown in fig. the bar carries a load of 20 KN at B. the cross section areas of steel and copper are 200 mm2 and 400 mm2 respectively find the stress in each rod ?if Es=210 GPa and Ec=83 GPa Copper rod 2m Steel rod- -1 m- 1m 2 m m- B 20 KN
Use the virtual work method to determine the deformation at joint B of the truss shown. 3 m A -2 m 100 KN B 50 kN -4 m- EA constant E = 70 GPa A = = 1,000 mm² C
The rigid bar is pinned at A and supported by two aluminum rods, each having a diameter of 1 in. and a modulus of elasticity ??? = 10,000 ??? and ?????? = 29,000 ???. The allowable stress of aluminum is 7.8 ksi and steel is 1.7 ksi. If the bar initially vertical,a. Determine the maximum P that can be applied.b. Determine the deformation of steel.c. Determine the deformation of aluminum.