A cantilever beam with a uniform flexural rigidity (EI=200 * 10^6 N.m2) is loaded with a concentrated force at its free end. The area of the bending moment diagram corresponding to the full length of the beam is 10000 N.m2 .Find the magnitude of the slope of the beam at its free end in micro radian?

A cantilever beam with a uniform flexural rigidity (EI=200 * 10^6 N.m2) is loaded with a concentrated force at its free end. The area of the bending moment diagram corresponding to the full length of the beam is 10000 N.m2 .Find the magnitude of the slope of the beam at its free end in micro radian?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given the beam shown below (E=200GPa, I=180x106 mm4, 80mmx300mm), do the following: a. Draw the shear force and bending moment diagrams b. Find the magnitude and location of the maximum tensile bending stress c. Using superposition, find the elastic curve and then the deflection of the beam at B, C, and D 8kN 4kN A B 4m 3m 3m
Hi, I want to find the location on the beam where the maximum bending moment happens as measured from point A. I have already gathered the following information. FAx= 0 FAy= 25.0869 FCy= 32.913 the sheer force at B= 3.087 The bending moment at B = 77.4785 Let the loading coefficents be: W1 = 4 kN/m, W2 = 8 kN/m Let the lengths be: L1 = 5.5m , L2 = 6m. If anyone could help me with this last step of the problem that would be great.
The bending moment diagram and cross-section for a beam are shown below. Use the elastic flexural formula ox = -Mzy/l, to determine the required strength of the beam to resist the compressive stresses. Circle the correct answer for the compressive strength in ksi: 2.3, 2.5, 27.5, 30, 37.7 Show your work below. Bending Moment Diagram Beam Cross-Section 4" +50 2' (K-Fe) 2" 2" - 40 2"
For the simply supported beam subjected to the loading shown, derive equations for the shear force Vand the bending moment M for any location in the beam. (Place the origin at point A.) Let a=2.75 m, b=5.00 m, PB = 60KN, and Pc = 80kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Answers: Ay = Dy= tel tel a i B a Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) PB B a PB Pc a C Pc C KN b KN D b D X D₂ X
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3 cm and internal diameter 2.3 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.6 cm from the neutral axis (i) The moment of inertia in (mm^4)= ii) The radius of curvature in (mm) = (iii) The maximum bending stress in (N/mm^2)= iv) The bending stress at the point 0.6 cm from the neutral axis in (N/mm^2)=
Consider the beam in the picture below: 7kN/m 5kN/m P N/m Section 1 Section 2 Section 3 - L/3 L/3 L/3 %3D Take P = the last four digits of your student number in N/m. If P<250 N/m then take P = 30OON/m instead. Take L = the third digit of your student number, reading left to reight. If this value is zero then take L = 2 Assume: The reaction at the Pin = V pin 47000L+9PL )N 54 The reaction at the Roller = Vroller = 61000L+9PL 54 and that both reactions act vertically upwards. a) Find an expression for the internal moment for Section 1. Show all working and any relevant free body diagrams. b) What is the maximum magnitude of the internal moment for Section 1? Mark sure you prove that the value you calculate is the maximum. c) Find an expression for the internal moment for Section 2. Show all working and any relevant free body diagrams. d) What is the maximum magnitude of the internal moment for Section 2? Mark sure you prove that the value you calculate is the maximum. e) Find an…
a) The second moment of area about the centroidal x-axis (IXXcentroid) for the solid homogeneous beam section shown below is 737,101.55 mm4. What is the second moment of area about the centroidal y-axis (IYYcentroid). Give your answer in mm4 to two significant figures. b) If the second moment of area (IXX) for the solid homogeneous beam section shown below is 917,387.73 mm4, determine the diameter d. Give your answer in millimetres (mm) to two decimal places.
Considering a uniform beam of 1 m long simply supported at both ends, theBending moment is given by the following relation:
Find the shear force and bending moment 1.5 m, 3 m, and 4.5 m from the left end of the beam. 9 kN/m 3 m Answer: x = 1.5 m: V = 3 m: V = 0, M = 27 kN • m x = 4.5 m: V = -10.125 kN, M : 10.125 kN, M = 18.625 kN·m %3D %3D 18.5625 kN · m %3D
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3.6 cm and internal diameter 2.4 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.5 cm from the neutral axis (i) The moment of inertia = ii) The radius of curvature is (iii) The maximum bending stress is iv) The bending stress at the point 0.5 cm from the neutral axis is
tf tw h W The dimensions of an l-beam are shown in the parameter table below. Find the area moment of inertia about the neutral axis, xx. parameter value units w 6.75 in 11 in tp 0.45 in 0.35 in Is in ||
A storage rack to hold the paper roll. Find force reactions and draw the shear and moment diagrams for the mandrel that extends half of the roll. Use singularity functions for this problem. Givens stanchion paper roll Density=984 kg/m^-3 OD=1.5 m ID=0.22 m L=3.23 m Density=mass/volume So W=(density*volume)*gravity Volume of hollow cylinder= (pi/4)(OD^2-ID^2)*Length of cylinder Length of mandrel=1/2 of L=>1.615 m mandrel base Assumptions: The storage rack is acting with a fixed support With a distributed load of "w" where w is the weight distrubuted