A cantilever beam of rectangular cross section (width b = 25 mm. height h= 100 mm) is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a to the vertical (see figure). Two strain gages are placed at point C. which also is at the midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle B = 60 to the horizontal. The measured strains are e 125 x 10 and e, -375 x 10-, Determine the force P and the angle a, assuming the material is steel with E- 200 GPa and = 1/3.

A cantilever beam of rectangular cross section (width b = 25 mm. height h= 100 mm) is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a to the vertical (see figure). Two strain gages are placed at point C. which also is at the midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle B = 60 to the horizontal. The measured strains are e 125 x 10 and e, -375 x 10-, Determine the force P and the angle a, assuming the material is steel with E- 200 GPa and = 1/3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A prismatic bar in tension has a lengthL = 2.0 m and cross-sectional area A = 249 mm2 .The material of the bar has the stress-strain curveshown in the figure.Determine the elongation d of the bar for each of thefollowing axial loads: P = 10 kN, 20 kN, 30 kN, 40 kN,and 45 kN. From these results, plot a diagram of load Pversus elongation d (load-displacement diagram).
A 5.1 m long simply supported wood beam carries a uniformly distributed load of 11.3 kN/m, as shown in Figure A. The cross-sectional dimensions of the beam as shown in Figure B are b = 205 mm, d = 460 mm, yH = 77 mm, and yx = 162 mm. Section a-a is located at x = 1.3 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) If the allowable shear stress for the wood is 850 kPa, what is the largest distributed load w that can be supported by the beam? х В L Figure A
find the normal strain if the figure is connected by rigid pins. v is poisson's ratio and E is young's modulus. width of strut is 8mm, height is 20mm. height increased by 0.01mm
9
The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (0.20 in., -0.55 in.). Assume a = 9 ft, b = 6 ft, and h = 7 ft. Determine the normal strain in each bar. B P b h
In the beam loading system given below, A is a simple and C is a sliding support. The outer diameter of the beam with a tubular profile is 180 mm, while the inner diameter is 140 mm. (a) Draw the normal stress distribution in the section at point B. (b) Draw the normal stress distribution in the cross section at the support C. (c) Find where the maximum stress occurs. 8 kN/m 12 kN 10 kN A B 2.5 m 2.5 m 3.0 m to
A 45° strain rosette (see figure) mounted onthe surface of an automobile frame gives the followingreadings: gage A, 310 X10-6 ; gage B, 180 X10-6 ;and gage C, -160X10 -6 .Determine the principal strains and maximumshear strains, and show them on sketches of properlyoriented elements.
The T-beam shown in the figure has cross-sectional dimensions: b = 200 mm, t = 17 mm, h = 300 mm, and h₁ = 280 mm. The beam is subjected to a shear force V = 47 kN. A h₁ h с Determine the maximum shear stress max in the web of the beam. (Enter the magnitude in MPa. Assume that the shear force acts parallel to the y-axis and is uniformly distributed across the thickness of the web.) 4.0654 Your response differs from the correct answer by more than 10%. Double check your calculations. MPa
Find the strain Stress=35 MPa E=42 MPa
Determine the normal strain AB and BC
Beam cross section is shown in Figure Q3 and given the second moment of area is I= 20.85 x 106 mm*. If a resultant shear force, Vacting at the beam cross section is 40 kN, (a) Determine the shear stress at point M, N, O and P based on the given shear force. (b) Sketch the shear stress distribution over the cross section and label the shear stress values V= 40 kN M 80 mm 40 mm y =100 mm 80 mm 80 mm 30 mm 80 mm Figure Q3
A strain element is given in the figure. Find the planes in which the normal stresses are equal in absolute value to the shear stresses.