A cantilever beam of length 6 m carries one-point load of 3 kN at a distance 6 m from the fixed end. In addition to this, the beam also carries a uniformly distributed load of 1 kN/m over a distance of 2 m at a distance of 3 m from the fixed end. Draw the shear force and bending moment diagram.

Q: 2.) A 9-m simple beam is carrying a uniform load of 25 kN/m over the entire beam with two-point…

A:

Q: A 5-m-long simply supported timber beam carries two concentrated loads as shown. If L = 18 kN and M…

A:

Q: A 7-m simple beam is carrying a uniform load of 25 kN/m over the entire beam with two-point loads of…

A:

Q: A 7-meter simple beam has one of its supports at the left end and the other is placed 3m from the…

A: A simply supported beam is loaded as follows

Q: 2. Calculate the maximum bending stress and maximum shear stress in the beam in Problem No. 1. The…

A:

Q: Given: Maximum positive shear = 387.50 kN Maximum negative shear = 602.50 kN Maximum positive…

A:

Q: A simply supported beam with length L = 4.0 m carries a uniform load w = 2.5 kN/m and a concentrated…

A: To find out the maximum bending moment in the beam.

Q: For a rectangular beam of 4 m long with 100 mm wide and 200 mm deep, it carries a shear force of 100…

A: Given- Rectangular beam span = 4 m, Width b=100 mm, Depth d=200 mm, Shear force SF=100 kN, It is…

Q: A beam of span 5 m is simply supported at both ends. It carries a uniform load of 6 kN/m throughout…

A: Length of beam = 5 mUDL on entire span = 6 kN/mSimply supported at both ends.The illustration of the…

Q: A simply supported beam with length L = 4.0 m carries a uniform load w = 2.5 kN/m and a concentrated…

A:

Q: A beam AB, 3 m long is hinged to a wall at end A and is supported by a tie rod DE which is hinged to…

A:

Q: 1. For the restrained beam shown below, compute the end moments (kN-m). 1 m 3 kN-m 1 m 1. What is M…

A: we will use slope deflection method to determine the Moment at the ends

Q: What are the support reactions at points A and B? What is the maximum bending moment and where does…

A: Step 1:Step 2:Step 3:

Q: The hollow rectangular cross-sectioned beam (200 mm wide and 400 mm deep with 10 mm thickness) shown…

A:

Q: A simply-supported beam carries a uniform load, w = 126 kN/m at its middle third. If L = 13 m,…

A:

Q: For the beam shown in the figure, a.Determine the degree of static indeterminacy, b.Compute for…

A: NOTE :- As per our guidelines we are supposed to answer first three SUBPARTS. So please post next…

Q: 2.) A 9-m simple beam is carrying a uniform load of 25 kN/m over the entire beam with two-point…

A: The answer is found to be a. Mid span deflection =35.47 mm ( downward) b. Deflection at 1.5 m =…

Q: Bending moment diagram for a overhanged beam is shown in figure. [Consider the supports at B and D]…

A:

Q: 3 - For the given beam, the shear force diagram is illustrated as follows. Determine the maximum…

A: We know that, the point where Shear force changes its sign, Bending moment is maximum at that point.…

Q: agrams for the beam shown below. 10 kN p= 20 kN/m

A:

Q: Determine the maximum bending moment that can occur at a point 8 m from the left support of a simply…

A:

Q: Q3: The beam shown in Figure 3 is subjected the moving load shown. Determine (a) the maximum…

A:

Q: A flat slab is supported on 600 mm dia circular columns spaced 8 m x 6 m apart in both directions.…

A:

Q: A 6-m simple beam is carrying a uniform load of 25 kN/m over the entire beam with two-point loads of…

A: A simply supported beam is simply supported by the supports and is stable in nature. The only way in…

Q: 14-m simply supported overhang beam is supported at x = 0 and x = 10m. The overhanging portion is…

A:

Q: An overhang beam is given in the figure. Which of the following bending moment is correct for the…

A: An overhang beam is given in the figure. Which of the following bending moment is correct for the…

Q: A simply supported beam AB = 10 m has a hollow rectangular cross-section with 17 cm as width, 28 cm…

A: As per guidelines we are supposed to answer only first 3 subparts

Q: 1. In the figure shown, is a vehicle having wheel loads of P; and P, at a distance of 1.8 m.…

A: Given: Two wheel loads 72 kN and 59 kN at a distance of 1.8 m are acting on a bridge having 15 m…

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.