14-m simply supported overhang beam is supported at x = 0 and x = 10m. The overhanging portion is from x = 10m to x = 14m (the overhang portion is 4m). A uniform 20 kN/m load is from x = 0 to x = 5m and a 30 kN concentrated

14-m simply supported overhang beam is supported at x = 0 and x = 10m. The overhanging portion is from x = 10m to x = 14m (the overhang portion is 4m). A uniform 20 kN/m load is from x = 0 to x = 5m and a 30 kN concentrated

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 8-m simple beam is carrying a uniform load of 25 kN/m over the entire beam with two-point loads of 15 kN at 1.5 m from both ends. If E = 200 Gpa and I = 0.000332 m, determine the following using the Double Integration Method:a.) Midspan deflectionb.) Deflection at 1.5 m from the left reaction.
A 4-m span simply supported beam carries a uniformly distributed load of 45 KN/m over its entire length. The cross-section is as shown in figure. Determine the maximum bending moment along the length of the beam (in KN-m). Determine the maximum moment of area of the cross-section (in mm3). Determine the maximum shearing stress in the beam (in MPa). Determine the maximum shear force along the length of the beam (in KN). Determine the maximum bending stress in the beam. (in MPa).
A simply supported wood beam carries a concentrated load of P = 8200 lbs as shown. The beam spans are L1 = 7 ft and L2 = 14 ft. The rectangular cross section has a width of b = 5.5 in. and a depth of d = 14 in. At section a-a, which is xa = 3 ft to the right of pin support A, determine the magnitude of the horizontal shear stress in the wood beam at point K, which is located yk = 4.5 in. below the centroidal z axis. H y Ун a Ук a B K L2 Answer: TK = i psi
A 1.6-m-long cantilever beam supports a concentrated load of P = 7.2 kN. The beam is made of a rectangular timber having a width of 120 mm and a depth of 280 mm. Calculate the shear stress due to the applied load at a point located d = 76 mm below the top surface of the beam. d 280 mm B 1.6 m 120 mm O 254 kPa O 156 kPa O 183 kPa O 204 kPa O 269 kPa Save for Later Attempts: 0 of 1 used Submit Answer
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 10 cm as width, 23 cm as depth and inner thickness as 2 cm is subjected to a point load of 8 N & 9 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 1 m & CD = 1 m. iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I = vi) Maximum bending stress = vii) Bending stress at 2 cm from the top =
only typed solution accepted
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 14 cm as width, 23 cm as depth, and inner thickness as 1 cm is subjected to a point load of 7 N & 5 N acting at C and D respectively and a uniformly distributed load (UDL) of 7 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 2 m & CD = 1 m. Solution: i) Reaction force at B = Answer and unit for part 1 ii) Reaction Force at A = Answer and unit for part 2 iii) The distance from B at which the shear Force value changes from "-" to "+" = Answer and unit for part 3 iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = Answer and unit for part 4 v) Moment of Inertia, I = Answer and unit for part 5 vi) Maximum bending stress = Answer and unit for part 6 vii) Bending stress at 1 cm from the top =
In the system shown in the figure, parts AB, BC and CD are of equal length and 4 m. Clockwise from point AA moment of 10 kNm is applied in the opposite direction. The distributed load of 3 kN/m at BC is upward. Beam DA load of 5 kN was applied downwards from the point. The profile of the beam has a 100 mm edge as seen on the right side.was formed by subtracting a circle with a diameter of 80 mm from the center of a regular hexagon of length. Accordingly; A)Calculate the reaction forces at B and C B)Draw shear force and bending moment diagrams C)Calculate the maximum bending and show it on the bending moment diagram. D)Calculate the sectional moment of inertia of the profile E)Calculate the maximum stress in the beam NOTE:For option C, you need to obtain a parobolic expression when drawing the bending moment diagram. You need to use derivation.
Show complete solution asap
An overhang beam carries a concentrated load, P and a uniform load, w = 15 kN/m. If the point of contra-flexure (where bending moment is zero) is located 0.5 m from support B, determine the absolute value of P (in kN). P (kN) w (kN/m) 2m A SM
CLO 2: A cantilever beam of span 12 m carries a triangular load that varies linearly from zero at the free end to 360 N/m at the fixed end. In addition, a 1000-N upward vertical load acts at the free end of the beam. What magnitude of a uniformly distributed load must be added throughout the span of the beam so that there is no flexural stress at the fixed end of the beam, in kN/m? 0.0333 0.0467 46.67 33.27
A 14-m simply supported overhang beam is supported at x = 0 and x = 10m. The overhanging portion is from x = 10m to x = 14m (the overhang portion is 4m). A uniform 20 kN/m load is from x = 0 to x = 5m and a 30 kN concentrated load is at x = 14m (or the right end). Find the value of the maximum positive moment.