cantilever beam has the cross-section of an isosceles triangle and is loaded as own in figure. If the moment of inertia of the cross-section I,= 1/36m“, then the aximum bending stress is 3 MN-m -1 m 10 m A. 1/16 MPa B. 36 MPa C 72 MDa

cantilever beam has the cross-section of an isosceles triangle and is loaded as own in figure. If the moment of inertia of the cross-section I,= 1/36m“, then the aximum bending stress is 3 MN-m -1 m 10 m A. 1/16 MPa B. 36 MPa C 72 MDa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A round bar have a radius 8 cm and subjected to an axial tensile force of 10 kN. Determine the axial…

A: Given data : Youngs Modulus (E)=70 GPaRigidty Modulus (G)=26 GPaPoisson's ratio=μRadius (r)=8…

Q: Typical units of strain are a. Inches and millimeters. b. Pound-inch, kip-inch, and…

A: Strain is produced when stress is applied . Stress is defined as the ratio of force per unit area .…

Q: A helical spring, with small slope of helix, is supposed to transmit a maximum pull of 2 kN and to…

A: Given data- A helical spring- Maximum pull = 2 kN, Extension of 10 mm for 400 N load, Mean diameter…

Q: A nylon thread is subjected to a 10 N tension force. Knowing that E=3.3 GPa and that the length of…

A: Given data : Change in length Original length=2.1100Force (P)=10 KNE=3.3 GPa

Q: Refer to the silty clay soil at the construction site in Problem 1. As part of a quality control…

A: Note : - Hi, thank you for the question. As per our Honor code, we are allowed to attempt first…

Q: From the given set of parallel forces shown. 40KN 60KN 100KN 60KN 50KN 2.5m 2.0m 4.5m 1.5m 1.5m…

A: For finding the resultant force we have to calculate ∑FY = 0

Q: Joseph Rivera Proportional Reasoning (Fractions and Decimals) Nov 11, 5:32:48 PM The table below…

Q: - What is the void ratio for a soil sample has a porosity of 40% The specific gravity of solids is…

A: Given data : Specific gravity of solid (GS)=2.70Porosity (n%)=40%Porosity is defined as the ratio of…

Q: A field pumping test was conducted from an aquifer of sandy soil of 4 m thickness confined between…

Q: An inverted tube differential manometer with an oil of specific gravity 0.8 is connected to two…

A: Given Specific gravity of oil,S.g.=0.8 Density of oil2=900kg/m^3 To find PA-PB=?

Q: 11. Determine the moment of inertia of the fully- cracked transformed section, I (in 10 mm). 12.…

Q: The bulk modulus of water is 2.0 x 10° N/m². The pressure required to increase the density of water…

A: Bulk Modulus of water =2×109 N/m2

Q: For the W310X97 section of A992M steel (Fy = 345 MPa), the in-plane of the web shear strength…

Q: A tacheometer fitted with an anallatic lens was used to observe the following: Instrument W.C. B…

A: Draw the figure.

Q: 1. For the beam shown in figure, determine the Ely at 2m from left support, 3m from right support…

A: We have to find value of EIy at 2 m from the left support and 3 m from right support and at free end…

Q: For the beam and loading shown, use the double- integration method to determine (a) the equation of…

A: Using double integration method W=5kN/m L=4m E=220GPa

Q: The velocity along the centreline of a nozzle of length L is given by V = 2t| 1- 2L where, V=…

Q: An overhang beam of uniform El is loaded as shown in the figure below. The deflection at the free…

Q: What is the Maximum Shear Stress, t, on the centric axially loaded member shown? The cross-sectional…

A: Given data : Axial load (P)=40 kipsCross sectional area (A)=2 in2

Q: Determine the normal stress in each segment of the stepped bar shown in Figure 4. Load P 20 kN %3D

A: Given data : Load (P)=20 KNForce in AB (FAB)=P=20 KN (Tensile)Force in BC (FBC)=-P+6P=5P=5×20=100…

Q: solve the problem 4

A: Given data in question Loads Span 7.5 m Simply supported beam To find out Moment at A and B

Q: For the truss shown in the figure, the magnitude of the force (in kN) in the member SRis 30 kN I 1m…

Q: Five rain-guage stations namely A, B, C, D and E are located on a circular shape basin of diameter…

A: Area other than A will be distributed equally for point B, C , D and E.

Q: Given that J is no. of joints. B and R are no. of members and no. of reactions. If B = 4, R = 3 and…

A: Introduction : A truss is structure made up of member jointed in the form of triangle . It consist…

Q: Probability of a 10 year flood to occur at least once in the next 4 years is (a) 25% (c) 50% (b) 35%…

Q: The diameters of a pipe at the sections 1-1 and 2-2 are 200 mm and 300 mm respectively. If the…

A: Given data : Diameter at section 1-1 (d1)=200 mmDiameter at section 2-2 (d2)=300 mmVelocity at…

Q: The thin walled cylinder diameter whose diameter is 6.24 meters and thickness of 15mm is subjected…

A: Explanation: Considering equilibrium For longitunial stress Brusting Force = restoring stress…

Q: The average velocity of the fluid in the

A: Given. Fluid flowing staedily in a circular pipe of radius R. Velocity distribution along the…

Q: 60 A square shallow foundation is to be constructed over a layer of sand. Given Df = 1 m; No is…

A: Given; Df = 1m ; qnet = 350 Kn/m2 sand is normally consolidated

Q: Iven: a. The weight of chunk of moist soll sample is 45.6 lb. b. The volume of soil chunk measured…

A: Given data : Specific gravity of soil solids (GS)=2.65Weight of moist soil sample (WMoist)=45.6…

Q: A 5-ft-long steel wire of 4-in. diameter is subjected to a 750-lb tensile load. Knowing that E = 29…

A: Given:- tensile force = 750 lb Diameter of rod = 1/4 inch Length of rod = 5 ft…

Q: Undrained shear strength of a clay is measured as 60 RPa. The unconfined compressive strength of a…

A: Given data in question Undrained shear strength Clay soil To find out Unconfined compressive…

Q: For a data of maximum recorded fiood of a river, the mear and standard deviation are 4200 m/s and…

Q: Determine the stresses in the two segments of the bar shown in the drawing. Segment A has a diameter…

A: To Find :- Stress in both segments of diagram

Question

Solve this

A cantilever beam has the cross-section of an isosceles triangle and is loaded as
shown in figure. If the moment of inertia of the cross-section lz= 1/36m, then the
maximum bending stress is
-1 m-
3 MN-m
10 m
A. 1/16 MPa
B. 36 MPa
C. 72 MPa
IDD. 1/36 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The rigid bar AD is supported by two steel wires of 1.5 mm diameter (E = 200 GPa) and a pinand bracket at D. Knowing that the wires were initially taut, determine the stress in each wirewhen a 1200 N load P is applied at D. What is the corresponding deflection of point D?
A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E-200 GPa. How much will rod CD elongate due to the load at B?
Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
Jertical beam of the applied to a shown. Determine forces are cross section compressive BC of the the maximum Stresses bRam. tensile and portion. 9,25 kN in 45mm I10mm 30 mm 30mm 400mm 500mm
a) Determine the force P (in kN) required to stretch the Aluminum bar by 3mm. B) Determine the final width and thickness of the Aluminum bar. (1)
As shown in the figure, aluminum, E= 70GPa links (1) and (2) support rigid beam ABC. Link (1) has a cross-sectional area of 320mm² and link (2) has a cross-sectional area of 480mm². For an applied load of P= 58kN, determine the rigid beam deflection at point B. (2) 4,000 mm (1) 2,500 mm B 1,400 mm 800 mm
If the beam is subjected to an internal moment of M = 30 kN-m determine the compressive bending stress in MPa on the top surface of top flange A. 50 mm 50 mm 10 mm M 150 mm 15 mm
The Figure below shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 800 mm² for AB and 400 mm² for AC. Determine the maximum safe value of W (kN) if the working stresses are 110 MPa for AB and 120 MPa for AC. ... B 40 deg. A 60 deg. A) 38.90 в) 55.30 61.70 76.2
125. A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm, respectively. An axial load of 12kN is applied on the bar. E = 2x105 N/mm2. The elongation of %3D the bar will be 1 (b) 6n 1 mm (a) mm (c) -mm (d) -mm 2
Use Method of Consistent Deformation to analyze the following statically indeterminate beams.(Determine the moments and reactions only)..Include Diagrams if applicable Thanks❤️
Prob 5. Calculate the maximum deflection dmax and the angle of deflection on the supports of a uniformly loaded simple beam loaded as shown. The maximum bending stress is o=60 MPa. The cross section of the beam is square with a length of 8 cm on each side. The beam is made of aluminum having modulus of elasticity E = 70 GPa. q = 2.0 kN/m L= 2.0 m
The system under the effect of torsion;a- Draw the torsional moment diagram.b- Determine the torsion angle CA (rotation angle) that will occur at point C.c- Determine the load shear stress.(G=80 000 MPa M1=5000Nm M2=4000Nm D1=120mm D2=90 D3=80 D4=60