A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20mm, is subjected to an internal pressure equal to the IMEP from item 1. Expressyour answers in MPa(a) Calculate the tangential and longitudinal stresses in the steel.(b) To what value may the internal pressure be increased if the stress in the steelis limited to 120 MN/m2?

Given a cylindrical steel pressure vessel having external diameter 400mm and thickness of 20mm, is…

Answered: (a) Calculate the tangential and…

(a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 120 MN/m2?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

P = 8kN. Using N = 3, determine the allowable stress for A501 grade steel. Calculate the dimensions (to 1 decimal place) of a square rod. L = 5.9m. Calculate the deformation (6) and the strain (€).
Question 4. Three wires are used to suspend the plate shown. Aluminium wires are used at A and B with a diameter of 3 mm and a steel wire is used at C with a diameter of 2 mm. Knowing that the allowable stress for aluminium (E = 72 GPa) is 96 MPa and that the allowable stress for steel (E = 200 GPa) is 124 MPa, determine the maximum load P that may be applied. L L P B
Round off final ans, dont round off initial values
An aluminium wire (E=10,600 ksi) having a diameter d=1/8 inch. and length L=14 ft is subjected to a tensile load P. If the maximum permissible elongation of the wire is 1/6 inch and the allowable stress in tension is 10 ksi, what is the allowable load Pmax? Answer in Ibs
The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa, Ebr 100 GPa. Figure P P -10 mm -20 mm 1 of 1 Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the steel. Express your answer to three significant figures and include appropriate units. Ost = Submit Part B Obr = Submit 0 Value If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the bronze. Express your answer to three significant figures and include appropriate units. Provide Feedback A Request Answer Value Units Request Answer Units ?
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: 24 KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 and E = 200 GPa, Determine the total resulting strain in the z- direction. Note: CN is the last 2 non zero digits of your cellphone number
SITUATION. A steel plate ABCD of thickness t = 5mm is subjected to uniform stresses: = 100 MPa 0₂ = -60 MPa. Ox E =200GPa, v= 1/3 a = 160mm and b = 200 mm Calculate the change in thickness (mm). -0.0023 mm 0.0023 mm O O 0.0045 mm - 0.0045 mm Ł B AL C D X
The aluminum bar ACDB is rigidly connected to a steel tube in CD. The data is presented in the table. If the load P is equal to 125 kN, determine: The stress of aluminum in segment AC. Answ: 63.66 MPa The stress of aluminum in segment CD. Answ: 13.93 MPa The stress in steel in segment CD. Answ: 39.79 MPa The total deformation of the bar. Answ: 0.29273 mm
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
As shown, an aluminium alloy construction BCD with a circular cross section is fixed at end B and affected by a force of 150 N at the free end D. The diameter of the cross-section a-a is 20 mm. The yield strength of the material is 80 MPa: a) Determine the stresses at point A of the a-a cross-section. As indicated in the picture, draw the stress element in Cartesian coordinates and specify the stress values.(b) Calculate the factor of safety, n for Tresca, and the von Mises yield criterion to see if the structure would yield based on the stresses at point A.(c) In the major stress area, draw the yield loci of both criteria and indicate the operational stress state & why is the Rankine failure criterion inappropriate for aluminium alloys?
4
A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positions indicated. 3 m 2.5 m C 1200 kN 900 kN 80mmØ 100mmØ E = 83 GPa Bronze E = 200 GPa Steel Which of the following most nearly gives the deformation of C? a. -0.7855 mm О Ъ. +0.8575 mm c. +0.7855 mm o d. - о.8575 mm