A buffer solution was prepared by mixing sodium acetate (0.3 mol/liter) and acetic acid (0.3 mol/liter) according to the table below Tube 1 CH3COONA( 120 ml) CH3COOH(ml 280 400 NaOH(ml) 50 50 Delta pH Calculate the pH of the acetate buffer in each test tube before and after the addition of 50 ml of a 0.2 M NaOH solution. 1). Calculated pH for Buffer 1: 2).calculated pH for Buffer 1 after addition of 50 ml NaOH solution 3). Calculated pH for Buffer 2

A buffer solution was prepared by mixing sodium acetate (0.3 mol/liter) and acetic acid (0.3 mol/liter) according to the table below Tube 1 CH3COONA( 120 ml) CH3COOH(ml 280 400 NaOH(ml) 50 50 Delta pH Calculate the pH of the acetate buffer in each test tube before and after the addition of 50 ml of a 0.2 M NaOH solution. 1). Calculated pH for Buffer 1: 2).calculated pH for Buffer 1 after addition of 50 ml NaOH solution 3). Calculated pH for Buffer 2

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

What is the pOH of a buffer that consists of 0.275 M methylamine CH3NH2 and 0.461 M methylammonium chloride CH3NH3Cl? Kb of methylamine is 4.5 x 10-4.
please help w/ 7 a,b,c,d
which titration Hd 12 0 8 0 answer curve best describes the expirimental set up below? shown 10 volume of titrant (mL) 20 of the a) strong base (beaker) and strong and (burette) b) strong acid (beaker) and strong base (burette) c) weak base (beaker) and strong acid e) we al acid (beaker) and acid (burette. strong base (burette).
If given 10ml of vinegar and told that 23ml of .4M NaOH was used to reach the end point during a titration: CH3COOH + NaOH → Na+CH3COO- +H2O A) Calculate the moles of Acetic Acid. (GMW: 60.0g/mol) B) Calculate the percent Acetic Acid (note: vinegar has a density of 1.005g)
3
What is the pH of a 1.0 L buffer made with 0.300 mol of HF (Ka = 6.8 × 10⁻⁴) and 0.200 mol of NaF to which 0.050 mol of HCl were added? Your submission: 2.742 Feedback: It looks like your answer is close but you may have made one or more rounding errors in your calculation OR you are including too many or too few significant figures in your answer. Check the math and significant figures you used to arrive to your answer and try again. I've tried 2.742 and 2.74. Both were incorrect and I have 1 more chance left.
A student added 501 mL of 0.35 M HCl to a buffer solution made up of 0.500 mol of citrate (A-), 0.500 mol of citric acid to 1.5 L of water (total volume = 1.5 L) (Ka = 7.41 x 10-4). A.) Calculate the pH of the initial buffer solution (before the addition of the acid). B.) Calculate the pH of the solution after the addition of HCl referenced above. C.) Did the buffer solution exceed its buffer capacity?
make a recipe with full written out steps for 100mL of the TES buffer 30 mM TES has pH of 7.2 and the pKa=7.55 4 mM MgCl2 4 mM NaCl 40 mM 2-mercaptoethanol acid and base stocks are 2 M MgCl2 and NaCl stocks are 0.5 M 2-mercaptoethanol stock is 1.4 M
What is the pH of a 1.0 L buffer made with 0.300 mol of HF (Ka = 6.8 x 10-4) and 0.200 mol of NaF to which 0.120 mol of NaOH were added?
Calculate the volume of acetic acid (in mL) required to prepare 150.0 mL of a buffer with a final concentration of 0.450 M and pH = 5.0 using 0.450 M acetic acid and 0.450 M sodium acetate (pKg = 4.7).
10:18 < 1 4 7 What quantity in moles of HCI need to be added to 200.0 mL of a 0.200 M solution of NaF to make a buffer with a pH of 3.10? (Ka for HF is 6.8 × 10¯4) +/- 2 LO Question 20 of 20 5 8 mol 3 6 9 O Tap here or pull up for additional resources Submit 97 X с x 100
#5 could you circle answers please