A BPO will be built in a reclaimed area inCebu City. Concrete piles will be used as itsfoundation with details and plans as follows:e -25-田田田田田田田田田C-1C-2田田田FOUNDATION PLAN• NGLNGLC-1C-2S750 mm2250 mm2000 mm2250 mmELEVATIONConcrete Piles - 450 x 450 mmC-1- 1800 x 2000 mmC-2 -1600 x 2000 mmThere 6 identical footings.Determine the total volume of disposal.田田田田田田田田田

Answered: Image /qna-images/answer/94586455-4eec-40cb-94cc-bde755f5c31f.jpg

A BPO will be built in a reclaimed area in Cebu City. Concrete piles will be used as its foundation with details and plans as follows: 田田田田田田田田 C-1 C-2 田田田田 FOUNDATION PLAN • NGL NGL C-1 5750 mm 2250 mm 2000 mm 2250 mm 2osomm ELEVATION Concrete Piles - 450 x 450 mm C-1 - 1800 x 2000 mm C-2 - 1600 x 2000 mm There 6 identical footings. Determine the total volume of disposal. 田田田田田田田田田田田田田

A BPO will be built in a reclaimed area in Cebu City. Concrete piles will be used as its foundation with details and plans as follows: 田田田田田田田田 C-1 C-2 田田田田 FOUNDATION PLAN • NGL NGL C-1 5750 mm 2250 mm 2000 mm 2250 mm 2osomm ELEVATION Concrete Piles - 450 x 450 mm C-1 - 1800 x 2000 mm C-2 - 1600 x 2000 mm There 6 identical footings. Determine the total volume of disposal. 田田田田田田田田田田田田田

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Pile foundation is proposed for 50 stories building in Dubai having a building foot print area of 20 m length and 20 m width and having a pile diameter of 800 mm and pile depth of 20 m near to the sea shore. The geotechnical investigation revealed a reclaimed land having the soil type mainly as well graded sand. The angle of shearing resistance was obtained by performing the direct shear testing as 36 degree. Use IS 2911 approach to obtain the feasibility of the construction of pile group foundation for this 50 storey building.
Q # 2. Discuss in your own words with the help of diagram, the load transfer mechanism in skin resistance-end bearing piles. Civil Engineering Subject= Geotecnical Design Plz type here
Explain the Procedure to form bulb-type uncased concrete pile.
Calculate the governing load combination for a secondary beam with effective width = 2.0 m Dead load Weight of slab = 3.0 kPa Ceiling services = 1.0 kPa Self-weight of beam = 1.0kN/m Imposed load - 0.2 kPa
1. Accurate quantities of steel works can be calculated from the detail reinforcement drawings. However, if working drawings and schedules for the reinforcement are not available it is necessary to provide an estimate of the anticipated quantities which generally is estimated in accordance with the requirements of the standard method of measurement of building works. Will 20m³ of structure be 1.904 ton for a warehouse and 35m³ of structure be 2.325 ton for a school? 2. The cross section of foundation is given in Fig. 2. Estimate the quantities of following items per meter length: 1) Earthwork in excavation in foundation trench; and 2) Lime concrete in foundation. 55.500 Ground level 55.150 55.000 300 Fig. 2.
Discuss the process of loading and load leveling and explain what quantitative technique are available to help in this process
What are the two, independent design criteria that all foundations (shallow and deep) must satisfy? O a. Settlement O b. Depth O c. Appearance O d. Low Cost е. Вearing Capacity
An ASD downward column load of 500 k is to be supported on a group of drilled displacement piles constructed in the following soil profile: Depth (ft) Soil Description Unit Weight(lb/ft3) Undrained ShearStrength (lb/ft2) Effective FrictionAngle (deg) 0–15 Silty sand 120 32 15–40 Clayey silt 112 500 40–60 Clay 110 600 60–70 Silty clay 112 1100 70–90 Sandy silt 114 1800 The groundwater table is at a depth of 15 ft. Determine the required number of piles, their diameter, and their length. No static loadtests have been conducted. Note that there are many solutions to this problem, but select a design that you feel is most appropriate.
Compare circular, square and I section piles in terms of usage, cost and advantages/disadvantages?
Would we see more settlement beneath the center of circular load or beneath the edge of load? and why? (kindly elaborate)
Describe the procedure to determine values for the coefficient of consolidation.
What is “block failure” in a group of piles and how does it differ from individual failure?