A bot surface at 100°C is to be cooled by attach- ing 3-cm-long, 0.25-cm-diameter aluminum pin fins (k 237 W/m - "C) to it, with a center to center distance of 0.6 cm. The temperature of the surrounding medium is 30°C, and the heat transfer coefficient on the surfaces is 35 W/m² °C. Determine the rate of heat transfer from the surface for a 1-m x 1-m section of the plate. Also determine the overall effectiveness of the fins. 0.6 0.25 .cm

A bot surface at 100°C is to be cooled by attach- ing 3-cm-long, 0.25-cm-diameter aluminum pin fins (k 237 W/m - "C) to it, with a center to center distance of 0.6 cm. The temperature of the surrounding medium is 30°C, and the heat transfer coefficient on the surfaces is 35 W/m² °C. Determine the rate of heat transfer from the surface for a 1-m x 1-m section of the plate. Also determine the overall effectiveness of the fins. 0.6 0.25 .cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Oil whose temperature is 30°C is flowed through a pipe with a diameter of 50 cm. The pipe is in an environment where the temperature is 20°C. So that not a lot of heat comes out of the pipe, the pipe is wrapped with an insulating material (k = 0.007 W/mK) as thick as 5 cm. If the convection coefficient of the outer surface of the pipe is 12 W/m²K, calculate the heat flow from the pipe per meter of length.
A 4-mm and 2-m-long electric wire is tightly wrapped with a 2-mm-thick plastic cover whose thermal conductivity is k =0.1 W/m-°C. Electrical measurements indicate that a current of 10 A passes through the wire and there is a voltage drop of 10 V along the wire. If the insulated wire is exposed to a medium at =20 °C with a heat transfer coefficient of h=10 T. W/m2.°C, determine the temperatures T1 and T2 as shown in the figure below. Also determine whether doubling the .thickness of the plastic cover will increase or decrease T2 T
A 15 cm x 20 cm hot surface at 85°C is to be cooled by attaching 4 cm long aluminum (k = 237 W/m-°C) fins of 2 mm x 2 mm square cross section. The temperature of surrounding medium is 25°C and the heat transfer coefficient on the surfaces can be taken to be 20 W/m²-°C. If it is desired to triple the rate of heat transfer from the bare hot surface, determine the number of fins that needs to be attached. plot the number of fins as a function of the increase in the heat loss by fins relative to no fin case (i.e., overall effectiveness of the fins) in the range of 1.5 to 5. Discuss the results.
Q2- A straight fin fabricated from aluminum (k = 237 W/m-K) has a thickness of 3 mm, a breath of 1 mm and a length of 15 cm is attached to a surface at 120°C. If the heat transfer coefficient is 12 W/m2-K at 40 °C, determine the rate of heat transfer from the fin and fin effectiveness when (a) the infinitely long fin assumption is used, (b) the adiabatic fin tip assumption is used.
Electrically heated draw batch furnaces are commonly used in the heat treatment industry. Consider a draw batch furnace front made of a 20-mm thick steel plate with a ther- mal conductivity of 25 W/m-K. The furnace is situated in a room with surrounding air temperature of 20 C and an aver- age convection heat transfer coefficient of 10 W/m2-K. If the inside surface of the furnace front is subjected to uniform heat flux of 5 kW/m2 and the outer surface has an emissiv- ity of 0.30, determine the inside surface temperature of the furnace front. I= 20°C Furnace front 4=5kW/m Air, 20 C h= 10 W/m K E=0,30 A= 25 Wim K Page 4.
A 1-in Sch 40 stainless steel pipe with a thermal conductivity of 45 W/m-K can move 1,000 kg of saturated steam per hour at 150 °C. Refractory material 0.25 inches thick with a thermal conductivity of 0.025 W/m-K insulates the pipe. At a temperature of 25 °C, the pipe is exposed to the outside air. There is a 1135 W/m2 internal heat transfer coefficient.40 W/m2-K is the outside heat transfer coefficient, whereas -K. Suppose that only the radial direction is involved in steady-state heat transfer and that radiation effects are negligible. ✓ Determine how much heat is being lost through these pipes to the environment.a. 399.1 W/mb. 1525.0 W/mc. 618.4 W/md. 1128.7 W/me. none of the above √ How about the insulated pipe's surface temperature?a. 118.5 °Cb. None of the abovec. 101.5 °Cd. 216.3 °Ce. 292.2 °C
700 W/m3 electrical heat is generated in a large plane wall whose one side is insulated while the other side is subjected to convection. The thermal conductivity of the wall is (k W/m.K) and the convection heat transfer coefficient is (h = 17 W/m?K). Determine the location and the value for the maximum temperature and the minimum temperature in the plate for steady one-dimensional heat transfer. Assume T. = 25°C. A=1 m?; L= 25 cm). = 20
A sphere ( k=204 W/m K) with inner diameter 4 cm and outer diameter of 8 cm . The inside temperature is 100C and the outer temperature 50 C . Calculate the rate of heat transfer
The wall of a furnace consists of a 0.85 cm-thick layer of steel (ks = 15.1 W/m/K) and an outer layer of brick (kb = .72 W/m/K). The outer surface temperature of the brick, To = 50oC, and is exposed to convection with air at 20oC providing a heat transfer coefficient of 150 W/m^2/K. Determine the steady temperature at the steel brick interface, Tmid, and on the exposed steel surface, Ti, if the brick layer has thickness Lb = 5 cm.
. Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k = 2.3 W/m °C, and surface area A = 20 m². The left side of the wall is maintained at a constant tem- perature of T₁ = 80°C while the right side loses heat by con- vection to the surrounding air at T = 15°C with a heat transfer coefficient of h = 24 W/m². °C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the rate of heat trans- fer through the wall. Answer: (c) 6030 W
Heat Loss by Convection and Conduction.A glass window with an area of 0.557 m2is installed in the wooden outside wall of a room. The wall dimensions are 2.44 × 3.05 m. The wood has akof 0.1505 W/m · K and is 25.4 mm thick. The glass is 3.18 mm thick and has akof 0.692. The inside room temperature is 299.9 K (26.7°C) and the outside air temperature is 266.5 K. The convection coefficienthion the inside wall of the glass and the wood is estimated as 8.5 W/m2· K; the outsideh0is also estimated as 8.5 for both surfaces. Calculate the heat loss through the wooden wall, through the glass, and the total.
In an experiment to measure the thermal conductivity of a plate of unknown material with area 1 m2 and thickness 0.1m, one of its surfaces is maintained at 100 °C and the other at 20 °C and a heat at the rate of 100 kW was supplied across it. Determine the thermal conductivity of the hot plate. Is the material metallic, non-metallic, or gas/liquid?