A boom consists of a 4-in.-diameter steel pipe AB and a cable as shown. The modulus of steel E = 29 × 10³ ksi. Determine the capacity P of the boom. Use the Euler formula with a factor of safety of 2.5. Neglect the weight of the pipe. Section properties of pipe: A = 3.174 in.² and the radius of gyration r = 1.51 in. 9 ft C A -12 ft- B P

A boom consists of a 4-in.-diameter steel pipe AB and a cable as shown. The modulus of steel E = 29 × 10³ ksi. Determine the capacity P of the boom. Use the Euler formula with a factor of safety of 2.5. Neglect the weight of the pipe. Section properties of pipe: A = 3.174 in.² and the radius of gyration r = 1.51 in. 9 ft C A -12 ft- B P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q.
PS
Column AB carries a centric load P of magnitude 16.5 kips. Cables BC and BD are taut and prevent motion of point B in the xz plane. Using Euler's formula and a factor safety of 2.2 and neglecting the tension in the cables, determine the maximum allowable length L. Use E = 29 × 106 psi. (Round the final answer to one decimal place.) P B W10 X 22 D The maximum allowable length Lis ft.
The lap joint is fastened with four ¾ inch diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets.
For a helical spring the slope of helix may be assumed small, is required to transmit a maximum pull of 1 kN and to extend 10 mm for 100 N load. The mean diameter of the coil is to be 100 mm. The diameter of wire is 100 mm. Calculate the no. of coils required? (G = 100 GPa and fs = 100 MPa)
SOLVE THE FOLLOWING DIFFERENTIAL EOUATIONS.
STRENGTH OF MATERIALS (UPVOTE WILL BE GIVEN. WRITE THE COMPLETE SOLUTIONS IN 2 DECIMAL PLACES. NO LONG EXOLANATION NEEDED. BOX THE FINAL ANSWER)
L13 L/2 L/2 B. A Prob. 5 (10 points) The figure shows a drill-rig pipe that is being picked up by a crane at point C. The pipe has dimensions L= 32 ft., do = 4. 50 in., and d; = 3. 60 in., and weighs 21 lbf/ft. At the moment when 0 = 30°, please calculate the principal stresses at: (a) the point marked B, and (b) at the point given by z = 0, y = do/2 at the same cross-section (i.e. at L/2 from the point A).
Determine the vertical and horizontal reactions of the hinge support if the weight of M object is FN Kilonewton, value of a = SN and b = MN meters. The equivalent of 0 is 30 degrees Note: MN = 88 FN = 88 SN = 47 a Hinge b Cable m Beam com M Rope
From the figure as shown, the cable BC supports the horizontal bar AB. Compute the shear stress at the hinge support at A having 20 mm Ø and at the pin support at B which has 30 mm Ø pin. The given views show how many of shear can be produced. Use 2 decimal places in every solved value. Pls include fbd.
Two cables exert forces on the pipe. Determine the resultant force (give the vector expression) and the angle 0 between the two cables F2 = 25 lb 6(00 30° 30°- y F = 30 lb
5.