A1 A block weighing 800 N is acted upon by a force P as shown. Knowing that the coefficient offriction between the block and the inclined surface are us 0.35 and uk= 0.25, determine themagnitude of the force P to start the block moving up the plane.-P25°O Zoom image529.51 N487.66 N780.42 N80 N (continuation)Determine the magnitude of force P to keep it moving up the plane at a constant pace.25°Q Zoom image648.67 N449.25 N780.42 N287.09 N(Continuation)Determine the magnitude of force P to prevent it from sliding down.25°Q Zoom image780.42 N79.99 N123.98 N648.76 N

Answered: Image /qna-images/answer/0ba484da-36ca-476e-a894-c06e294e9dd7.jpg

A block weighing 800 N is acted upon by a force P as shown. Knowing that the coefficient of friction between the block and the inclined surface are us 0.35 and uk=0.25, determine the magnitude of the force P to start the block moving up the plane.

A block weighing 800 N is acted upon by a force P as shown. Knowing that the coefficient of friction between the block and the inclined surface are us 0.35 and uk=0.25, determine the magnitude of the force P to start the block moving up the plane.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Nut 17.0 N 37° 25.0 cm

A: The text provides the following information:The force applied to the wrench is 17.0 NThe distance…

Q: find the center of the given shape

Q: Express Fas a vector in terms of the unit vectors i, j, and k. Determine the angle between Fand the…

Q: -26-ト-26→ -3b 26 ---x

Q: Q1: Find the resultant force and the component force F for the system shown below (fig 1) using…

A: Calculated the resultant force and the component of force F for the system using parallelogram law.

Q: DRAN THE 1SOME TRG VIEW

A: Isometric view for the given orthographic views is drawn on the isometric grid paper. 1 Grid = 1…

Q: Consider the following steel shaft with varying shaft diameter. Determine the rotation of D with…

Q: The crankshaft of a two-stroke engine spins at about 391 RPM for a brake torque of 983 N-m. If the…

Q: PO 8 in.

A: Redraw the following figure for the given question.

Q: The distance between the corresponding point on the screw thread when measured parallel to the axis…

A: Create: It is the peak edge of a screw thread, that connects the adjacent flanks at the top. Flank:…

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: For the objects shown below sketch the object in the space provided after rotating it about the axis…

A: Find Rotate the object about the given axis.

Q: - х a = 6 in b = 0.7 in C = 2 in

Q: Redraw when the rack AB is at 45o angle. What are the other two angles belonging to the triangle…

Q: 15 kN 20 kN 2 m m

Q: y b a a = 9 in b = 1.2 in с 3 2.4 in

A: Find the centroid distance in inches.

Q: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

A: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

Q: Give the number of DOF and its type for each robot shown in Fig.Q1B:

A: Given:To find:Number of degrees of freedom and type of each robot.

Q: M 50 10 60 M. 10 10 50

A: Let’s divide the section into three different sections as shown – Calculating area of the different…

Q: A vehicle is running in a longitudinal way. Suppose the input x(t) is the acceleration, and the…

Q: determine (a) the required value of a if the wn is to be vertical, (b) the corresponding 30° 200 N

Q: please solve the centroidal Ix, centroidal Iy, Ix and Iy of the attached figures. Underline/box…

A: Given Shaded zone To find Moment of inertia

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

Q: Determine the moments of inertia for the cross-sectional area of the member shown in the Figure…

A: Moment of inertia of an area is defined as the product of area and the distances of its center from…

Q: Consider (Figure 1). Figure 0.3 m. 120° 45° 60⁰° 325m Y Part A Determine the magnitude of the…

A: Given data: Force (F)=260 N To find:-the magnitude of the moment of the 260-N force about the x…

Q: please solve the centroidal Ixc, centroidal Iyc, Ix and Iy of the attached figures

Q: If the allowable tensile stress of the wires AB and AC is oallow = 250 Mpa, determine the largest…

Q: Determine the angle 0 between the edges of the sheet-metal bracket. -400 mm 250 mm 300 mm 50 mm y

Q: 150 m 50 mm 85 mm Section X-X 20 kN

Q: Please solve the centroidal Ix, centroidal Iy, Ix and Iy of the attached figures. Underline/box…

A: Given Shaded areas To find Inertia for section 1 About X axis About Y axis Inertia for I area About…

Q: (Determine the (f_x ) when force 80 N and angle 30° on the axis (X .A 69N .B 69.28lb .C 69.28N .D…

Q: 1-8. Determine angles a, b, and c (Figure P1-8). a 35° FIGURE P1-8

Q: Describe the Parallel-Axis Theorem for an Area?

Q: Wire BC, has a diameter of D. and made of A-36 steel, is used to support member AB at B as shown.…

Q: Fy = 16 kN O Fy = 4 kN O Fy = 2 kN O

Q: 1 mm 10 mm 1 mm Y axis 5 mm 10 mm 1 mm X-axis

Q: Move the forces in the shape to point a

Q: Determine the area of the shaded region. The value of b is 4 inches. Write the numerical value only.…

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

Q: Determine the moments of inertia of the unequal angle shown relative to the axes shown.lx, ly and…

A: Given:To find:

Q: In order to pull out the nail at B, the force F exerted on the handle of the hammer must produce a…

A: According to the question data MA=200lb.inclockwise and the figure We need to find Force F to…

Q: Determine the magnitude of the equilibrant force acting on point O in Newtons. Given that FA = 781…

Concept explainers

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.

Question

A block weighing 800 N is acted upon by a force P as shown. Knowing that the coefficient of
friction between the block and the inclined surface are us 0.35 and uk= 0.25, determine the
magnitude of the force P to start the block moving up the plane.
-P
25°
O Zoom image
529.51 N
487.66 N
780.42 N
80 N

(continuation)
Determine the magnitude of force P to keep it moving up the plane at a constant pace.
25°
Q Zoom image
648.67 N
449.25 N
780.42 N
287.09 N
(Continuation)
Determine the magnitude of force P to prevent it from sliding down.
25°
Q Zoom image
780.42 N
79.99 N
123.98 N
648.76 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given data

VIEW

Calculations

VIEW

Final solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Handwritten please. 30-40minutes
c) Sketch the stress distribution in the section X-X
Resolvet he ysolb fovce intoeom ponentsacting latong members ABandAC 30 45 450
11 The volume of a cube with sides of L is L'. If the length is measured as 121 +2 mm, determine the worst possible error in the volume.
slove f
Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 8 5 إجابتك
Determine at for ce of He trurs Shown mem bers 3 6०० 4m
For machine element, locate the centeroid
Resalue (Fnd the Gampantats) F into compadents alang the u and v axes : 150 N and determine the Magaitude of these compunents
Not Secure-alfarahidiuc.net 3- Determine the moment of inertia of the area shown about thex axis. 150 mm 30 mm 100 mm 100 mm O a-771102828 mm4 Ob-817303822 mm4 Oc- 371104150mm4 ارسال الاجابة السؤال السابق السؤال التالي
determine the location of the Centriod. length x=87 mm
The system shown is in static equilibrium and motionless. Consider the 10 kN force as "the load" on the system. • The coefficient of static friction at a rope/shaft interface is 0.25. • The coefficient of kinetic friction at a rope/shaft interface is 0.16. NOTE: • Submitted responses shall be to 4 significant figures. Do NOT use scientific notation. Find: 8. The angle of wrap around the upper-left shaft is 9. The angle of wrap around the lower-right shaft is 10. The maximum magnitude of the force P that will not initiate upward motion of the load is rad. _kN. 11. The minimum magnitude of the force P that will not initiate downward motion of the load is _kN.