Wire BC, has a diameter of D. and made of A-36 steel, is used to support member AB at B as shown. Determine the value of the force P (kN) that causes a decrease of D in the diameter of wire BC. The values of the original diameter (D.) of wire BC, D, L, and L, are given in table below. L1 В 400 mm

Wire BC, has a diameter of D. and made of A-36 steel, is used to support member AB at B as shown. Determine the value of the force P (kN) that causes a decrease of D in the diameter of wire BC. The values of the original diameter (D.) of wire BC, D, L, and L, are given in table below. L1 В 400 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.76P: The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.

See similar textbooks

Related questions

Q: Determine the minimum cross-sectional area of a steel bar required to support a tensile force of 50…

A: Given Data⇒Tensile Force=50 KipsAllowable unit tensile stress=20 KsiProblem definition⇒Problem says…

Q: Rod BD is made of steel (E = 29 × 106 psi) and is used to brace the axially compressed member ABC.…

Q: Determine the largest weight “W” that can be supported by the two wires AB and AC. The working…

Q: The homogenous bar that weighs 5000 lb is supported by a pin at C and a cable that runs from A to B…

A: Given data Weight (W) = 5000 lb dimaeter of cable (d) = 0.8 in To determine Axial stress in the…

Q: A polystyrene rod consisting of two cylindrical portions AB and BC Is restrained at both ends and…

A: The normal stress in portion AB and BC.Given:The length of the segment AB is .The length of the…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F1 = 30…

A: Solution:

Q: An aluminum rod to be used in an aircraft control system is 600 lb 600 lb required to stretch 0.12…

A: Given data as per question Tensile load =600 lbAllowable stress =17 ksiYoung's Modulus =10.2×103…

Q: 2. For the bone shown to the left, assume the cross-section at C can be approximated as annular,…

A: Given:Average normal stress, σ=3.8 MPaLoad applied, P=1200 Nouter diameter, d=25 mm

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

100%

Wire BC, has a diameter of D, and made of A-36 steel, is used to support member AB at B as
shown. Determine the value of the force P (kN) that causes a decrease of D in the diameter of
wire BC. The values of the original diameter (D.) of wire BC, D, L,, and L; are given in table
below.
L1
В
400 mm
-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

do not shortcut pls. 4 decimal places
The pole is supported by a pin at C and an A-36 steel guy wire AB. B. 3 ft 30 2.5 kip 4 ft Part A If the wire has a diameter of 0.3 in., determine how much it stretches when a horizontal force of 2.5 kip acts on the pole. Express your answer to three significant figures and include appropriate units.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F; - 32 kips. F2 - 10kips, Fs- 24 kips, and F4- 39 kips, determine the absolute value of the axial load in rod (2). O 6 kips O 2kips O 4 kips O 17 kips O 11 kips
Please help me find the solution to this problem. Thank you! ASAP!
P = 93.3 N Determine the force at F. Take it apart to help you solve
Need only a handwritten solution only (not a typed one).
P2-4. A loading causes the block to deform into the dashed shape. Explain how to determine the strains eAR, EAC, EBC. (YA)zy- The angles and distances between all lettered points are known. B C B' 7C A D P2-4
Determine the magnitude of the pin force at B.
= A system of three steel (E = 30, 000 ksi) pipes is loaded and supported as shown below. The loads are applied to the rigid plates that connect the pipes at B, C, and D. Determine the change in length of the complete system of pipes if the cross-sectional areas of pipes AB, BC, and CD are 1.2 in², 1.0 in², and 0.8 in², respectively. A 14 in B 16 in -30 kip с 20 in 5 kip D 15 kip
Determine the magnitude of the pin force at B. 0.52 m A 0.33 m 0.33 m 240 N-m 0.33 m B Answer: B = i
The homogenous bar that weighs 5000 Ib is supported by a pin at Cand a cable that runs from A to B around the frictionless pulley at D. If the diameter of the cable is 0.8 inch, calculate its axial stress. Express your answer in ksi (kips per sq. inches) with one decimal place only (Note: Give only the numerical value of the answer. DO NOT INCLUDE THE UNIT IN THE ANSWER) * D F 3 ft 5 ft 5 ft
i provided u with the answers in the second