A benchmark program is run on a 60 MHz processor. The executed program consists of 104,000 instruction executions, with the instruction mix and clock cycle count given below. Determine the effective CPI, MIPS rate, and execution time for this program.

Q: For the instruction being executed: add $s1, $s2, $t0 use the following delays for each…

A: Explanation: First, read the registers. and, Instruction access memory. and, Decode and register…

Q: For a given number of instructions, assume CPI is increased by 20%, and clock cycle time is…

A: The CPI is increased by 20%, so we can add 0.20 to CPI The clock cycle time is decreased by 20%, so…

Q: ote: sclon Sundwame OT J01n0 Consider the two computers A and B with the clock cycle times 100 ps…

A: The user has to consider the two computers A and B with the clock cycle times 100ps and 150ps…

Q: A processor executes a program in 10 seconds with average CPI and IC of 2 and 20*10° respectively.…

A: Answer: Given: Arithmetic 7 Store 5 Load 7 Branch 6 Total 25 Instructions Cycle…

Q: Table Q3 (a) lists the content of a program memory that consists of four (4) lines of AVR machine…

A: Answer: I have given answer in the handwritten format

Q: Suppose we have two implementations: Machine A has a clock cycle time of 10 ns. and a CPI of 2.0.…

A: The solution is given below with calculation Happy to help ?

Q: A typical computation program is run on a 20 MHz processor. The executed program consists of 50000…

A: Provided the solution for above given question i.e effective CPI and execution time for given…

Q: f an instruction takes 1 nsec and a page fault takes an additional n nsec, give a formula for the…

A: Answer :--   1 + n/k neno second

Q: Determine the INSTRUCTION PE, CONTENT/RESULT of the destination after the execution (if not…

A: ADC instruction:  It stands for ‘Add with Carry’. For this add the content of  register with the…

Q: A Program is running on a processor Pl and it has the following parameters: lc is equal to…

A: See below for complete calculation.

Q: Amdahl’s Law is as applicable to software as it is to hardware. An oft-cited programming truism…

A: (a) Consider, 90% of a program is made to run 10 times as fast. Fraction of work performance…

Q: Computer A has an overall CPI of 1.3 and can be run at a clock rate of 600MHz. Computer B has a CPI…

A: Given :  Computer A has an overall CPI of 1.3 and can be run at a clock rate of 600MHz. This program…

Q: A Program is running on a processor Pl and it has the following parameters: Ic is equal to…

A:

Q: A benchmark program is run on a 40 MHz processor. The executed program consist of 100,000…

A:

Q: A program consists of 100,000 instructions as follows: Type of Instruction, IC, and CPI Instruction…

A: solution 1st processor CPU execution time = instruction count × average CPI × clock cycle. Total…

Q: two different processors execute same instructions, Processor one has 4Ghz clock rate and 1.5 CPI,…

A: Performance of Processor = clock rate * CPI. Number of cycles = execution time*clock rate Number of…

Q: pe 1 instructions require 1 cycle to finish. pe 2 instructions require 4 cycles to finish. pe 3…

A: Introduction: The CPU executes instructions of different types that require varying amounts of time…

Q: 1. A program has 5 billion instructions is running with a CPI of 2 on a machine with a 2.5GHZ…

A: CPU time= instruction count (IC)* clocks per instruction (CPI)* clock time (CT)

Q: A computer with a 32-bit word uses an instruction format that includes direct and indirect…

A: The answer given as below:·

Q: A CPU has a frequency of 2GHz and can execute code with three types of instructions: 1. Type 1…

A: We need to find the number of instructions per second for the given scenarios.  ***As per the…

Q: Compute the CPI for a computer that runs its workload composed of two programs. Program 1 runs…

A: We have:- Program 1 runs 1865751 instructions using 12451317 clock cycles. Program 2 runs 10114053…

Q: Consider the two computers A and B with the clock cycle times 100 ps and 150 ps respectively for…

A: For solving the problem let’s assume that number of instructions in the program is I. Now, as per…

Q: Consider two computers, P1 and P2, of the same instruction set (ISA). We have cogram of 7.5x10°…

A: Answer is given below

Q: Consider two computers, P1 and P2, of the same instruction set (ISA). We have a program of 7.5x10º…

A: When comparing the performance of two computers, we need to consider various factors such as clock…

Q: Subject name: Microcomputer Principle Application Determine the data in AL after the following…

A: The answer is given in the below step

Q: calculate the rate of MIPS by executing a program that has 600 MHz processor and 1 million…

A: Total execution time = Total CPI*Total # of instruction*clock cycle time.    Total CPI = 0.3*1 +…

Q: Assuming the same instruction mix listed in Problem 7, what is the average execution time across all…

A: Given the instruction mix: R-type: 40% Load: 20% Store: 15% Conditional branch: 25%

Q: Orthogonality arises when the design of an instruction set provides a "backup" instruction for each…

A: The following are the items that are required for the CPU to function properly: The programme cannot…

Q: two different processors execute same instructions, Processor one has 4Ghz clock rate and 1.5 CPI,…

A:

Q: 1.13.2 [10] In general, these CPI values are larger than those obtained in previous exercises for…

A: The answer is given below with proper explanation