Draw timing diagram for the following instructions: i. Instruction: LHLD 3400H Corresponding Coding: X-5 77 X-4 00 X-3 34 Instruction: LXI B 3400H Corresponding Coding: X-2 5D X-1 00 X 34 Instruction: XTHL Corresponding Coding: X+1 3E Instruction: SPHL Corresponding Coding: X+2 3E Here X = 10[Last two digits of your ID]. So, if your id is 2014000000129 then X= 1029H X+1=102AH, X+2 = 102BH etc. V. vi. vii.

Draw timing diagram for the following instructions: i. Instruction: LHLD 3400H Corresponding Coding: X-5 77 X-4 00 X-3 34 Instruction: LXI B 3400H Corresponding Coding: X-2 5D X-1 00 X 34 Instruction: XTHL Corresponding Coding: X+1 3E Instruction: SPHL Corresponding Coding: X+2 3E Here X = 10[Last two digits of your ID]. So, if your id is 2014000000129 then X= 1029H X+1=102AH, X+2 = 102BH etc. V. vi. vii.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Determine the value after the instruction (signed division). AX=0020H DL = FCH IDIV DL Select the correct response: FF08H FFF8H 00FBH 00005
(d) The table below shows the ALUcontrol signal of the datapath we discussed in class. Instruction Funct ALU Орсode ALUop ALU action operation field control Iw 00 load word XXXXXX add 0010 Sw 00 store word XXXXXX add 0010 beq 01 branch equal subtract 0110 XXXXXX R-type 10 add 100000 add 0010 R-type 10 subtract 100010 subtract 0110 R-type 10 AND 100100 AND 0000 R-type 10 OR 100101 OR 0001 R-type 10 set on less than 101010 set on less than 0111 You want to add the bne instruction into the datapath, which already includes the required hardware for the instruction. Write out the ALUop for bne and how you can determine whether the bne results in the branch to be taken.
Select an instruction that tests bit position 8 of register CH. Select the correct response: None of the choices BT CH, 8 TEST CH, 128 a or b
Determine the value after the instruction (signed division). AX = 0020H DL = FCHIDIV DLSelect the correct response:A. 00005B. FF08HC. 00FBHD. FFF8H
The instruction used to fill DX with the its sign bit is: * CWD SAR DX, 1 SAR DX, SF SHR DX, CL SHR DX, SF SAR DX, 10 SAR DX, [SF] SAR DX, 16
ASSEMBLY The ROR instruction is only suitable for signed integers. True False
Rebuild the instructions a-INC CX b- SUB AL02H c-SUB AX,DX
Draw the timing diagram for the following instructions : Instruction: LXI 3400H Corresponding coding: 1017 77 1018 00 1019 34
An NOTX instruction's size would be: 1 byte 2 bytes 3 bytes 0 bytechoose the right answer
If AX=910AH, the instruction (CWD) will: O Change AX to FFFFH Charige DX to 0000H O Change AX to 1111H O Change AX to 0000H Not be executed O Change DX to 910AH Change DX to FFFFH O Change DX to 1111H
Decode the instruction is the third phase in Fetch-Execute Cycle. 1 - True 2- False
What is the value of the register DX after the instruction? DX = 78F4H AX=45D9H AND DH, AL Select the correct response: 5845H 58F4H 7858H 78D9H