A beam is simply supported at the left end and is fixed at the right end. It is subjected to a concentrated service dead load of 50 kN at its midspan. Assume the beam to be laterally supported continuously throughout its length and has a compact section. Span of beam is 6 m. Prop. of beam Zx 990 x 10³ mm³ Fy = 248 MPa Sx = 316.5 x 10³ mm³ a) Determine the max. concentrated service live load that the beam could support. b) Determine the safe concentrated load that could be carried by the beam using ASD method.

A beam is simply supported at the left end and is fixed at the right end. It is subjected to a concentrated service dead load of 50 kN at its midspan. Assume the beam to be laterally supported continuously throughout its length and has a compact section. Span of beam is 6 m. Prop. of beam Zx 990 x 10³ mm³ Fy = 248 MPa Sx = 316.5 x 10³ mm³ a) Determine the max. concentrated service live load that the beam could support. b) Determine the safe concentrated load that could be carried by the beam using ASD method.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the force member DE. O 218 DE = KN. Compression O 320 4-6. -6 44>6 -6 O 210 75 kN |100 kN 75 kN O 111 D 25 kN - 25 kN- E O 119 33 O 315 B 413 O 297 K H 14 Dimensions in meters
determine the reacction of th beam show in fig by using consistante deformatiom method . use the redundants Cy and Ey
A simply supported rectangular beam of length 6.45m has a width of 390.5mm and an effective depth of610.5mm. The beam is to be reinforced using 12 ?? bars. The beam supports service dead loads ofWd = 13.5kN/m and WL = 35.5kN/m. f'c = 28Mpa and fy=420 MPa Given: b= 390.5 mm d= 610.5mm L= 6.45 m Wd = 13.5 kN/m WL = 35.5 kN/m 1. Calculate the ultimate moment capacity of the beam.2. Calculate the height of the equivalent stress block.3. Determine the number of bars required for this beam.
Title: Design of Beam in Flexure (WSD Method) PROBLEM: Design the beam to resist the loads shown. Take fc = 9 MPa, fs = 124 MPa, n = 11, bar diameter = 20 mm. Take b = d/2. Use WSD method. As (Gomm 20 KN lo Ka/m 8 KN/m 3m
a beam b = 350mm h = 660mm is reinforced with 2- 28mm compression bars and 4- 36mm tension bar. concrete cover is 60mm from centroid of the bar, if The beam is subjected to a maximum service dead load of 230KN m. determine the maximum service live load the beam can carry. use fc = 21Mpa, fy = 345MPA Select the correct response: MII = 244.02KN-m MII = 390.43KN-m %3D MII = 666.43KN-m MII = 436.43KN-m
Determine the reactions of A & B for the steel bon and leasing as given abuming that 4.5 mm clearance exist bin the bar and the ground before the loads are applied. Assume E = 200 GPG. P₁ = 300 KN P₂ = 600 KN A₁ = 250 mm² A₂ = 400 mm² 5 R 4 3 2 1 & P VA 0 B P₂ 150mm 150m 150mm 150mm 4.Sm
Determine the force in member DI of the loaded truss. Enter a positive number if in tension, negative if in compression. 4L B 5 m Answer: DI = i Save for Later 6L 6L D E 6L -5 m E H |Η 5 m AB=BC=CD= DE = EF = FG 4L L F L G Attempts: 0 of 1 used Submit Answer
4. The column shown below carries a factored load Pu = 1000 kN, Mu = 224 kN. The frame is braced against sidesway, k = 1.0. Determine the adequacy of column. Use Cm 1.0, Bd 0.20 f'c = 21 MPa, fy = 276 MPa. en Pu Mu 450 Pn 3.5m Lu mm 8 - 6 28mm OMu 75 150 150 75 Pu 450
A wooden beam AB supporting two concntrated kaods Phan a rectangulic crons sechion of width ti - 100 mm and height h-150 mm. The distancer trom each end of the beam to the nearest load is a - 0.5 m. The span of the beam is 5 m. Calculate for the total lerngth of the segment of the beam. in meters, that is sutjected to a constant bending monent.
STATICS OF RIGID BODIES. PLEASE ANSWER ASAP THANK YOU FOR A RATE
6. 20ft P= 20K Mmax CA A max =
Need help asap pls.