A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. Reaction forces are positive upwards and couples are positive counter-clockwise unless otherwise stated. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 13 kN/m, L = 7.2 m and El = 5.9 x 104 kN-m² is constant for the beam. Answer: (a) Ay= i Mc = i (b) Vmax Mmax i = i B kN kN kN.m KN kN.m

Q: A motor operates at 1800 RPM and expends 2 HP.  How many ft-lbs of torque does it provide at that…

A: Given data: The speed of the motor is; N=1800 RPM. The power of the motor is; P=2 HP.

Q: b. Number of Links: L= Number of joints: J₁= Number of half Joints: J₂= Mobility = c. Number of…

A: In these drawn mechanism, we need to find the number of lower pairs (binary joints) and higher…

Q: Some homes that use baseboard heating use copper tubing. Hot water runs through and heats the copper…

A: Mass of the copper tube,(m)=540 g. Initial temperature,(T1)=15.01oC Final temperature,(T2)=25.48oC…

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A: Answer: 1.Final answer:The direction of the force on the moving charge is (c) South.Explanation:When…

Q: In 1960 the German company Krupp Steel Works constructed the spherical pressure chamber for the deep…

A: Let the  volume of sphere be V. The density of sea water is 1025 kg/m3 and density of air is 1.2…

Q: А3 size, in mm, is О 210х 297 О 148 х 210 О 297 х 420 О 8.27 х 11.7 O O O O

A:

Q: While taking a break from the Extreme Beer Fest in Boston, you decide to do something educational…

A: Draw the diagram for the given movements for a better understanding of the question and final…

Q: A seesaw that weights 45lbs and its 5m long is balanced on the fulcrum in the center.  1- Two…

A:

Q: A team of professional thieves wants to knock down a castle wall using a primitive explosive. At…

A: Given: total mass of the explosive(M) = 40 Kg and it breaks into three pieces as shown below:

Q: 0.2 m B 0.2 m 1.3 m 0.7 m A P Circular

A:

Q: The hand writing is not very clear :(

A: Basically the miller indices are the set of numbers which define the particular plane in the crystal…

Q: Why you put h= 19 instead of h=38 your answer for the exercise is incorrect can you please correct…

A:

Q: The radial stress in thin cylinders 2 points can be neglected because: the thickness of thin…

A: Radial stress is stress due to fluid pressure in the cylinder acting radially outwards, it is…

Q: What are the units of F in the equation below: F = mg/gc where m is mass in lbm; g is acceleration…

A: Given;m is the mass in lbm (pounds mass).g is the acceleration due to gravity, which is given as…

Q: FA -X B FB Alpha = 34 degrees

A:

Q: A stepper motor is used to drive an x-y milling machine table. If the step angle of the motor is 1°…

A: Given, Step angle of the motor, α=1°Pitch of the lead screw,p=7mmSpped, V=25.0mm/sDistance moved by…

Q: A mobile crane has a 25 ft long boom (OA). The center of gravity (G1) of the boom is located at its…

A: Draw the F.B.D of the truck.

Q: 8. Three ships A, B, C are located as follows: A is 48 km due north of B and C is 125 km due east of…

A:

Q: Single pipe with pump) Without the pump shown in the figure below it is determined that the flowrate…

A: The power absorbed by the pump can be calculated using the formula give below as- P=ρgQhf where, P…

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: gure 4.00 in 1.25 in A single-scoop ice cream cone is a composite body made from a single scoop of…

A: Given:

Q: A business equipment room has 1000 watts of lighting and some small motors with a total output of 10…

A:

Q: Find a "flat" object in your house, make necessary measurements, and then calculate the center of…

A:

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: Change following into SI units (MKS): (c) 2 hours

A: Change following into SI units (MKS):   (c) 2 hours

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.